(800) 853-2651
SHOP NOW

Recent content by SteveB(wi)

Yesterday's Tractor Forums
  1. S

    My 8N

    They make poly or rubber cutting edges for snowplows. Untitled URL Link
  2. S

    '52 8N-B Distributor Upgrade to Pertronix Ignitor?

    http://www.pertronix.com/docs/instruction-sheets/1244AP6.pdf Untitled URL Link
  3. G

    OT-Ford Explorer Alternator

    I know some of the gents on this board are either professional mechanics or are close to the repair industry. I need some advice on a Bosch Alternator. I replaced the original alternator on my wife's Ford Explorer about seven weeks ago, and now the replacement Bosch from NAPA is shot. Is...
  4. C

    Massey Update Pt 7 (Videos)

    I posted yesterday about how to use my timing light to try and figure the timing out. I used my phone's flashlight and peered into the timing hole and I can't see any marks on the flywheel at all. This is stopped, at idle or high idle. I've uploaded two videos, one shows me with the...
  5. A

    new additions to the funnyfarm....

    Pile of real gogetters......... Australian Sheperds @ 1 week old....
  6. 4

    Need To-35 information about the ZB-134 engine.

    What can you tell me? I'm gathering information about it. I'v had it over 15 years and used it a lot. It's still a working tractor,just not used as much. Engine has ID. tag riveted to the block along with a warning tag. I'l see if I can post some pictures and let them speak. :) ___JIM
  7. J

    New Gen Gauge supplier

    Has anybody found any new Gen gauges they really like- seem well built and look orginal and you would recommend them and the supplier? Specifically I have a 5020, 4000 (gas), 3010 and 4010 restorations to start in a month or so and I'm looking for nice replacement gauges. Last year I had a...
  8. T

    Stuck Engine and Head Removal

    I just picked up a 52 8N with a stuck engine. The previous owner said it had been sitting in a barn for 10-15 years, and he had taken the head off and filled the cylinders with diesel fuel within the last year, but he was unable to free it. Since it already had the head off, I filled the...
  9. M

    Help ID'ing a tractor - think it is a IH 240U

    I'm looking at an older International Loader from a family member, hoping to get into a loader cheaply and possibly get a backhoe on it later. From digging around it looks like a 240 Utility, there is no pto or 3 point. Looks like just a drawbar as there is a 55 gallon barrel of weight back...
  10. R

    Setting up a new fuel pump on a 770

    I just rebuilt my 770 and as a part of the overhaul I installed a new pump. This is one of the ones from eBay that was intended for a 780B. Tractor starts immediately and surges from 350-550 rpms. Will not rev beyond that regardless of throttle position. Shut off allows full range...
  11. S

    Removing crank pulley on the WD-9

    I saw somewhere in my research that a bearing separator should be used in conjunction with a 3 jaw puller to remove the crank pulley. Is that absolutely necessary? Are there any other ways to get the pulley off? As long as I am asking, are there any tricks to getting the set screw out (other...
  12. B

    Possible for rotor to be too low in distributor?

    Could this scenario be possible? I bought a new distributor cap and rotor for my International S120 last year. Over the past year it has had this intermittent problem where it will just stop, or sputter and die and then after I fiddle with the points sometimes it will start again then be ok...
  13. John P.

    Trouble getting AGCO Parts

    Is there an AGCO Dealer left in this country who still knows how to look up Oliver Parts?
  14. K

    What are these wheels from???

    [url] https://photos.yesterdaystractors.com/gallery/identify/id6343.jpg
  15. T

    HEY Queen B

    we missed you and the R man Saturday in Lexington.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top