(800) 853-2651
SHOP NOW

Recent content by SteveTn

Yesterday's Tractor Forums
  1. S

    12 V. conversion for a Cub

    I bought a kit from Charlie for my 48 Cub. Switched to 12v because I wanted to use my 12v sprayer with it. Great guy to work with and kit worked great.
  2. S

    Ford 3600 Temp

    Thx. Rod
  3. S

    Ford 3600 Temp

    Don't have IR heat gun. Did take a look at this weekend again. Once cranked, takes awhile as it should for the needle to move. Drove it around a little while and the needle went about a 1/4 inch into the red. Checked the coolant in the radiator and it was warm not hot. After it idled down, the...
  4. S

    Ford 3600 Temp

    Hmm. Didn't think of that possiblity. Gives me something else to look at. Thx. Rod
  5. S

    Ford 3600 Temp

    Had to replace alternator on my 3600 last weekend. Cranked up to check to make sure alternator was working and after running about 15 minutes noticed temp gauge moving into red so shut it down. Checked radiator and liquid was warm not hot. Cranked up next morning and seemed to run fine never...
  6. S

    Cub Gear Oil

    Thx. Always better to ask the stupid question.
  7. S

    Cub Gear Oil

    Regarding '48 Cub transmission, steering and final drive, I see Rotella has 2 gear oils 80W-90 & 85W-140. Would one of these be a good choice? Thx
  8. S

    New Farmall Cub

    Thx. to all for the advise. I"m sure I"ll have a lot more questions as I go along. Waiting for my manuals to come in then will be ready to go.
  9. S

    New Farmall Cub

    Thx. for the info. Just ordered a manual this morning as after reading a lot of posts a little confused even on the oil. Had read some that say use 10W 30, but now seeing some others that say differently. What are you using? Thx
  10. S

    New Farmall Cub

    Hi to all. New to the forum and Farmall tractors, so got a lot of questions. Just bought a Farmall cub S/N 18717 to play with. Seems to be a "48. Runs very good. Trying to change all of the fluids. Got the oil. Could use some advise on the transmission & hydraulics i.e where"s the drains, fills...
  11. S

    Just Finished

    Nice work!
  12. S

    Ford 7000 Restoration 98% Complete

    Good looking tractor. Great job!
  13. S

    morbid pictures :)

    Should have been a disclaimer before showing those pics :-)
  14. S

    OT - I'm a grandpa!

    Congratulations! Expecting my first in about 3 weeks. Can't wait to get a picture of her on the 3600 with 'ol Grandpa :-)
  15. S

    NOW ready to mow!

    Yeah, she's too pretty, needs a little dust on her....Nice job!
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top