(800) 853-2651
SHOP NOW

Recent content by Strokedpoked

Yesterday's Tractor Forums
  1. S

    Crankshaft welding

    I’m just wondering if anyone who has ever built up a crankshaft with an mig or stick welder would care to share the type of filler metal used for the process.
  2. S

    Billet Rods

    Who would be the go to for a set of billet rods for a JDA if that matters? Thanks
  3. S

    Prairie village Madison SD

    Does anyone have or know where to find the rules and classes for their Thursday night Antique pull? Thanks
  4. S

    Sub-arc welder

    Thanks. I’ve been trying to locate a place that can provide analysis of material but have been unsuccessful. I’ve got a 2 cylinder deere crank that needs a journal welded up and I would like to give it a try but don’t really know where to start, I believe they are forged steel.
  5. S

    Sub-arc welder

    I know this is old thread, but what filler would you use for your mig journal repair?
  6. S

    JD 6-1 powerblock re-sleeve?

    Everything is there to run the power block, just needs to be resleeved. I certainly wouldnt want to go any smaller.
  7. S

    JD 6-1 powerblock re-sleeve?

    Yeah but there isnt much for alternative blocks currently that doesnt require a specific cylinder head. So Im going to try to save it if I can.
  8. S

    JD 6-1 powerblock re-sleeve?

    Anyone that has resleeved a John Deere powerblock, are both of the bores for the sleeves at the front (head) and the back (case end) the same or did they put a narrow bore up front and tapper the sleeve? Thanks in advance.
  9. S

    John Deere crank builders

    Its been a while since I have looked for a crank, are there any reputable crank builders/welders out there yet particularly for an A or G crank.
  10. S

    Big bore John Deere A

    Block or crank? Im in need of a block some time soon, just dont know how big of a bore I can safely put in front of my crank and get a few good years out of it.
  11. S

    Big bore John Deere A

    Looking for opinions on a 7 bore block in front of a welded crankshaft with a 3 pin. How long do you think it will last?
  12. S

    Pulling hitch

    JDTH, Tim, great guy great product 763-350-0555
  13. S

    JD G starters

    28MT
  14. S

    1.5 e series jd

    thanks, ill give it a try!
  15. S

    1.5 e series jd

    Thanks for the reply! I'll have to do some looking around online and see if I could find some sort of diagram.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top