(800) 853-2651
SHOP NOW

Recent content by stumpjumper400

Yesterday's Tractor Forums
  1. M

    case 780 b backhoe hydralic cylinders piston nut torque

    i amrepacking the cylinders on a 780 b hoe i am starting with the stabbilizer cylinder s any one know what the torque for bolt on the end of the rod for the piston i takes a 1 13/16 socket i have not got the bolt out yet to see the thread size or pitch thanks hud
  2. R

    MF20 IND 3 point hitch weight limit

    I was sure I posted this once but I do not see it? If it turns up as a duplicate then I guess I screwed up. I have to build a new counterweight for my MF20 IND and I want to know what the weight limit is on the 3 pt. hitch. I have all the manuals and I cannot find any reference to weights in there.
  3. C

    12 volt electrical issue

    I’ve recently rebuilt a ford 8n tractor got it all wired up put a new one wire alternator , coil , wiring harness ,resistor , terminal block ,etc.. and when I put a digital volt meter on the battery while its running my meter fluctuates randomly between 13 to 18 volts an in between . I also put...
  4. S

    Proof meters and cables

    Yes sir.......I turned the tractor over while looking at the hydraulic pump adapter to make sure I was spinning it in the right direction. I was warned about turning it the wrong direction. It unravels the spring cable. Steve
  5. S

    Proof meters and cables

    When you say cleaned it, did you soak it in solvent to get everything off or just wipe it clean? YT is sending me a new gauge and cable when they figure out how to get just the gauge because they only sell the kit of all gauges. Steve
  6. S

    Proof meters and cables

    The first cable did not get stuck to the meter. The nipple was sheared off on the pump end. The second new cable is the one that's stuck to the proof meter. I think the meter itself hit a snag internally. While trying to turn the cable by hand, there is a definite snag. When I turned it by the...
  7. S

    Proof meters and cables

    What has the experience been with the proof meters and cables from this site? I bought the gauge kit for my 841 and a new metal cable. The meter worked for about 10 minutes of run time. When I removed the cable, the keyway spline that goes into the hydraulic pump was sheared off. I ordered...
  8. S

    Jubilee pto shaft replacement

    I was just pointing out that if the seal is good then it won't leak back into the differential as stated after you put the shaft back in and level the tractor. I guess if you knew exactly how much to lift the rear without combining the sumps then your all set. If it can be done. I don't know...
  9. S

    Jubilee pto shaft replacement

    If the seal is good and it leaks forward when you pull the shaft out then wouldn't extra fluid be trapped in the hydros when you put the shaft back it? Just saying. The seal between the two was good on my 801 and it's not that much younger than a jubilee. If you drain the sumps, it's not a hard...
  10. S

    1964 ford 4000 hydraulic lift not working

    The "release" or unloader valve is in the lift cylinder housing so yes it is under the lift cover. You didn't say whether you had the manual for it or not. If you don't, get one. It was very helpful in rebuilding mine. I found out yesterday that the rebuild worked for my non functioning lift...
  11. S

    10si wiring

    I'll put a diode in while I wait for the light assembly. Maybe some didn't see where I was confused on the numbers vs. letters. The directions and or schematic I am following are from this site at http://www.yesterdaystractors.com/cgi-bin/viewit.cgi?bd=ford&th=344550. If the alternator...
  12. S

    10si wiring

    The "R" is not mentioned and the "F" is on the other number. I just wanted to get an opinion before I burn it up and have to buy another alternator.
  13. S

    10si wiring

  14. S

    10si wiring

    That is how the other post read.
  15. S

    10si wiring

    Like I said in the earlier post, the letter identifiers are different.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top