(800) 853-2651
SHOP NOW

Recent content by sycamoreview

Yesterday's Tractor Forums
  1. S

    Ford Early 2000 Hydraulic Lifting Issue

    So when my friend bought this tractor, the arms were stuck up, and when digging into it, the fluid was badly contaminated with water. I worked the unloader to free it up since it was stuck, but I think you bring a fair point, I will get a ITT manual and do a whole refresh of the insides.
  2. S

    Ford Early 2000 Hydraulic Lifting Issue

    Any thoughts anyone?
  3. S

    Ford Early 2000 Hydraulic Lifting Issue

    Hey Forum, I have what might be a quick question. I am working on a friends 2000. We had an issue, and I solve it, the arms were stuck up, unloader valve just needed to be freed. So it can lower which is good, latest issue, and I cannot figure what to do. When tractor is on, and lift lever is...
  4. S

    John Deere FFB Grain Drill Question

    Since the gate and assembly was shattered, I was lucky to get a housing from a suppler that holds old stock, and a new gate and feeder from JD. However, the new feeder/gate is a little off spec compared to the old ones.. ill need to modify the shaft when im looking for something to do over the...
  5. S

    JD4020 Hydraulic issues

    Will be sure to check that too,
  6. S

    JD4020 Hydraulic issues

    No loader on it, all new fluids and filter, and clean screen. The non shifting wont go from part to anything, like you cant pull on it, happens when all the hydraulics are being used, like lift arms up and a implement in the air (trailer plow). I am going to get a gauge kit and ill borrow a...
  7. S

    JD4020 Hydraulic issues

    Problem is, sometimes its fine, then 10 seconds later, eh its slow, then its back 15 seconds later. Very odd... I will say, when moving it actually operates better, sitting no. I've also tested increasing RPMs when parked, it helps, but depends.... Also I did notice, sometimes the transmission...
  8. S

    JD4020 Hydraulic issues

    Its a Syncro, and I have the same behavior with and without the clutch pedal depressed.
  9. S

    JD4020 Hydraulic issues

    I will do,
  10. S

    JD4020 Hydraulic issues

    Hey any ideas what I should try next before replacing front steering seals? If not, ill just proceed with doing front seals,
  11. S

    John Deere FFB Grain Drill Question

    Fair enough, I am going to assume the middle / 'coupler' is a roll feeder. I'm going to cut it since its quicker, and I can find 5/8 square stock to remake it. I'll post back what becomes of it.
  12. S

    John Deere FFB Grain Drill Question

    Hey Forum, I am trying to repair a frozen feed cup, gate, whole assembly etc. one of the cups is shattered in the middle of the one side. My question is, I have unbolted everything, and there is no way I can remove cup to cup due to everything locked up and wont move, I was wondering, is the...
  13. S

    JD4020 Hydraulic issues

    Well this fell behind apologies, I only recently got to servicing all fluids. It didn't change anything. Screen was pure clean, and filter didn't look that bad. Pump still chatters here and there, and under the dash the same.. What's next to look for? :)
  14. S

    JD4020 Hydraulic issues

    I think someone might have topped it off with ISO 46 for me the other day.. ill deff dump all the fluid and use Hy Gard or J20C Spec.
  15. S

    JD4020 Hydraulic issues

    Is it fine to use ISO 46 oil for the Hydraulic fluid ?
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top