(800) 853-2651
SHOP NOW

Recent content by Tejon

Yesterday's Tractor Forums
  1. T

    2-bolt and 3-bolt mount starters

    More very interesting information. I was thinking that the nose would interchange with a 2-bolt unit. I may get a 2-bolt starter and see how it works out. However, contacting a remanufacture or rebuilder will be done to hear what they have to say since they work with these starters all the...
  2. T

    2-bolt and 3-bolt mount starters

    I should have put power to the starter but then if I had there would have been someone asking did it turn the engine over (ha,ha) and the engine doesn't matter. However, the valve cover was removed for valve train inspection and there are a couple valves stuck so no further action taken on the...
  3. T

    2-bolt and 3-bolt mount starters

    It could very well be a replacement section... I could have a Frankenstein tractor. It has Lambert disc brakes 3-bolt covers, and a flip up rear seat that has a base to be mounted to a tool box or under seat battery box. Tractor doesn't have a battery box under fuel tank but has the mounting...
  4. T

    2-bolt and 3-bolt mount starters

    Hmmm how do I answer this.... What's to know about an old starter outside of the attributes on the starter to match up in order to purchase a new starter. I don't need to know if the starter works or not if I desire to purchase a replacement starter. Never said the tractor was running and...
  5. T

    2-bolt and 3-bolt mount starters

    Now this is information I haven't heard about.. very interesting This the casting numbers on the clutch housing and what is stamped on the starter data tag. There isn't a data tag on the clutch housing. The engine is stamped X 1 and that is gasoline. The engine cover has a M on it so I...
  6. T

    2-bolt and 3-bolt mount starters

    Putting power to it FIRST would be the first step I agree but what if it didn't work that would bring us to where I'm at now. I don't have heavy duty soldering irons and was never any good at soldering. I am proficient with a gas welding torch and have the items needed except empty out of date...
  7. T

    2-bolt and 3-bolt mount starters

    Jim.M, Current starter has the stud. No idea if the starter is operational at all. I should put a jumper cable to it and see if it spins. I have not taken it apart to check for field shorts, bushing wear, brush issues, nothing. Just trying to source another starter to have on hand. I agree...
  8. T

    2-bolt and 3-bolt mount starters

    I think I need to add more information for clarification and repeat. 3-bolt mount starters are available but only in the style that requires a saddle mount switch, a activation lever arm, and a pull rod for the lever arm. This is what I am finding. I am looking for a 3-bolt mount starter...
  9. T

    2-bolt and 3-bolt mount starters

    Farmall M (from what I have read) used 2-bolt and 3-bolt starters with the external threaded stud to connect to the battery cable. I can only find the 2-bolt mount starters. Can I swap the 3-bolt nose to the 2-bolt nose starter?
  10. T

    Tappet in oil pan

    Back to used red MN: Your response was nice and intelligent and of course opinionated. Did Op ever mention anything about a "misfire"? NO!! Your comment "In essence I hope it conveyed that I believe that finding that part in the engine and the fact that the engine is locked are NOT LIKELY...
  11. T

    Ford 801 PTO engagement cable

    Will you ever learn.............................
  12. T

    Tappet in oil pan

    ford8ntractor purchased a STUCK engine not operational.
  13. T

    Tappet in oil pan

    Going in the right direction...tear that critter down and you will find the reason of being stuck. Might even have extra parts left in there from a prior tear down, 😃, it happens may not have anything to do with the stuck engine. You said the engine was stuck at purchase not running so I'm not...
  14. T

    Farmall M Ausco-Lambert disc brakes

    As I have found the Lambert brake system is very Obsolete at least for the 3-bolt cover style as I have. Found a lot from searching the forum. Thanks for the replies and the those that looked.
  15. T

    Farmall M Ausco-Lambert disc brakes

    Is there a service manual for the Ausco-Lambert disc brake set up used on the Farmall M tractors?
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top