(800) 853-2651
SHOP NOW

Recent content by Tennessee Wayne

Yesterday's Tractor Forums
  1. T

    GMC COE

    Anyone on here have an intrest in the GMC Coe or LCF? I recently purchased a 1957 370. 2 1/2 ton. Engine runs great, transmission and most everything works. Just spent $1000 getting brakes on it, new wheel cyls.(8) New Hydrovac, new lines, ect. Don't think its had any brakes in 20 years. Got to...
  2. T

    Old GMC single axle tractor

    I have a 1957 GMC 370. Its a COE_LCF_ or stub nose, whichever you want to call it. Its a 2 1/2 ton single rear axel. Not a 5th wheel for a trailer. The front looks like the one pictured above, with the swing out engine access doors. Its all original and came with the Pontiac 270 straight 6 cyl...
  3. T

    GMC COE

    I know its probably 55 to 59 But cannot determine the exact year model. If anyone has the resources to look it up, I would be greatful. Serial# t372 s100 35e 6 cyl. engine 270 19500 Gross Wt. Single headlights. Cab: 1762 I dont have a pic on computer yet. Forgot to write it down, but think it...
  4. T

    What are these machines worth?

    I cannot see a serial tag on the 420. If its missing, collectors will not be intrested. Its only value will be if you want to keep it. You can get replacement tags from Deere, but they are a joke (nothing like the originals). That appears to be a 420T with optional wide front. The tag may be...
  5. T

    420 All Fuel

    I have a 420W serial number 86925. Does anyone have the info to tell if this tractor came out an All-Fuel model? Only thing it has is the oil pan with petcock. No other clues, no extra hole in hood, ect. I posted this on the other site and no help, except to have 2-Cyl to research it, and that...
  6. T

    40 hydraulics

    The drifting down is probably caused by worn piston seals, then the draft control causes it to jump back up. If you have the service manual, you could try changing the crossover valve lever, under the seat, to dual or single operation and see if this stops it. Could be just one piston causing...
  7. T

    Carb adjustment

    If your tractor is an M, Mt, 40, 420, 430 with the marvel s. carbureator. The L shaped needle on bottom of carb. is the load needle. Manual says with tractor in neutral, throttle in wide open position, turn the L shaped screw IN until engine sputters,,,then OUT, one or one and half turns will...
  8. T

    John Deere 40 vineyard?

    Couldnt find your photo of the axels. But if it has a serial tag it should have 40s 40v 40w 40u ect. Just looking at the rear picture, the depth control and final drives and fenders, it looks like a 40w. If it is a 40w, then the rear axels have been cut off probably, because the 40w was a...
  9. T

    JD 420

    The service manual covers this. Adjustment is made by removing or adding washers inside the oil pump. Just remember, if you remove the oil pump, you will have to reset the timing with the distributor.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top