(800) 853-2651
SHOP NOW

Recent content by tgrist

Yesterday's Tractor Forums
  1. T

    1964 mf 65 power steering cylinder. still leaking

    I just got back from the hydraulic shop and it brought up a concern that the small hole might be too small. It is quarter-inch FIP and the other 3/8 in. so the new pump in the pictures is compatible with American threads. what is on my tractor currently looks just like the picture Tom from...
  2. T

    1964 mf 65 power steering cylinder. still leaking

    This message is a reply to an archived post by Phil Tibbetts on March 07, 2021 at 07:17:58. The original subject was Re: 1964 mf 65 power steering cylinder.. As it turns out I rebuilt the cylinder but did not rebuild the valve, because the 2 Allen head screws that can be removed to prevent the...
  3. T

    PHOTOS of rebuilding my Massey’s Power Steering Cylinder

    I have the exact same problem with ball bearings in the Allen head screw holes. I know this post is quite old but I'm hoping someone can help. my question is how did the valve Rod get removed without being able to unscrew it via the Allen head holes? I rebuilt the rest of the cylinder and...
  4. T

    Fuel Injection Pump Governor Spring Position

    how did you determine the code for the pump? I am having the same problem as the op with a mf65
  5. T

    14T- Why can't it bale around turns?

    still?
  6. T

    14T- Why can't it bale around turns?

    thank you for the explanation I actually did not know what that meant. And yes I have opened up the baler before starting to bale. I tried out the modifications today, the baler seems much happier. The noise and fear of complete destruction is considerably reduced while going around...
  7. T

    14T- Why can't it bale around turns?

    "One option would be adding an equal angle hitch similar to later model pto operated equipment. This EA hitch addition could be accomplished utilizing 2''b thick x 4'' wide x 12'' long piece of metal a Cat ll bolt-on draft pin & Cat ll weld on ball/socket"
  8. T

    14T- Why can't it bale around turns?

  9. T

    14T- Why can't it bale around turns?

    I got it in phase. the drive shaft is rectangular and a U joint yoke was Square. I fit the square hole into the rectangular Peg. instead of drilling I welded it together.quite poorly I might add. this was cobbled together by the previous owner. if you look closely you can see that the...
  10. T

    14T- Why can't it bale around turns?

    I think it's lined up correctly but it still seems off by a tooth. and is my end drive shaft wrong too?
  11. T

    14T- Why can't it bale around turns?

    I have a slightly different set up then that. I have the collar around the drive shaft with the two ears that stick out.
  12. T

    14T- Why can't it bale around turns?

    so it looks like every single connection is out of phase? is that correct?
  13. T

    14T- Why can't it bale around turns?

    I see other Balers continuing to operate while turning online. I am trying to bale enough to feed a few rescue horses, I cut and bale on small properties 3 acres or less. what used to be a what used to be a hay field is now a subdivision. The landowners allow me to make use of the grass they...
  14. T

    mf135 3 cylinder gas pto lever position

    This message is a reply to an archived post by Samn40 on July 04, 2016 at 01:56:41. The original subject was Re: mf135 3 cylinder gas pto lever position. I just made that mistake. I think this picture will fix my problem. I cleaned the filter and replaced the PTO inspection cover/shifter, and I...
  15. T

    PHOTOS of rebuilding my Massey’s Power Steering Cylinder

    I didn't read this until today. but that right click thing works perfectly. the pictures would have been very helpful but I already rebuilt the cylinder.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top