(800) 853-2651
SHOP NOW

Recent content by TheBoro

Yesterday's Tractor Forums
  1. T

    Snow Plow Edge

    Works Great. From the first plow to the last of the season. The "all-thread" makes it so I can raise and lower the pipe as needed.
  2. T

    Front Spindle Bolt

    I had the same problem trying to find a tapered pin. TheOldHokie made me two of them. They both were perfect. I had a lot of wear on the spindle, so I had to fill the wear with my welder first and grind it back to size. I highly recommend him. I'd email him! TB
  3. T

    Spindle Welding

    Thanks so much, Bill. I appreciate the help!
  4. T

    Spindle Welding

    1941 9N Front wheel spindle/arm: I need to put a few beads of weld on my spindle in the notch where it meets the arm. It is worn where the bolt needs to keep everything tight. Question is... Do I need to preheat the spindle before I weld it? Using a Lincoln Buzz Box, any...
  5. T

    Arm Bolt needed...

    Hey folks- I need a new one of these for my 1941 9N... I looked in NComplete and Dennis Carpenter's books with no luck. Can I just use a carriage bolt? Thanks!
  6. T

    Won't turn over... jumped it...

    Oh good...you said easier right? What do I have to do with the 9n? Can I just follow my FO4? Do you have any tips for the job? Or pics?
  7. T

    Won't turn over... jumped it...

    Thanks guys... I put it in neutral and used a wrench. Fired up. So its the round starter switch then? Can I clean it up or replace?
  8. T

    Won't turn over... jumped it...

    Thanks! Cables - bright and tight, right? switch... what would I be looking for with that? Can I test it?
  9. T

    Won't turn over... jumped it...

    41 9n 6v. Compression is LOW, but it started and ran great all winter for plowing. Week ago it started hard, then stalled out from not letting it warm up enough. Tired to restart with no luck. Figured that the battery was too low. Tried it a few times, until no noise from the starter...
  10. T

    OT - how to put gravel back after snow plowing?

    yea, I use my blade too. I have the front mount dozer blade that I use to plow snow with. It is what puts the stones there in the first place, so I figure it is the best tool take'em back. Before I take the plow off in the spring I use it one more time to push the stones back into the...
  11. T

    Some fun summer pics with Fords...

    Hey Pete- Where abouts in upstate NY does all of this fun happen? I am always looking for this type of fun to go see! I am outside of Utica. Thanks!
  12. T

    Newfie's -gotta love 'em !

    Awe.. you got me excited with the word "Newfies"... I thought that you were talking about the dog breed!!! This is mine at 7.5 mos. old.
  13. T

    OT If You Are Easily Offended, Pass This By.

    [i:5e0556de74]-Normally I try to stay away from the politics and such... but I liked this. I guess that I am a southerner at heart! [/i:5e0556de74] [b:5e0556de74]Are you a nnalert, a nnalert, or a Southerner? [/b:5e0556de74] Here is a little test that will help you decide. The answer...
  14. T

    Trencher

    HA! I bet. As long as I can incorporate the N into the project I guess I will be happy! Maybe even riding over the replaced dirt after the job is done to "pack" down the dirt!!! Thanks again!
  15. T

    Trencher

    Yea, that makes sense. Thanks for the quick replies, guys. Guess I will check out my plow options. Appreciate the help! TB
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top