(800) 853-2651
SHOP NOW

Recent content by tinny

Yesterday's Tractor Forums
  1. T

    John Deere 112 mower deck

    Found the problem the tension pully bracket was bent up just a tad. Bent it back and now can mow. All bearings and spindles were quiet and tight.
  2. T

    John Deere 112 mower deck

    The deck has very little rust. I will have to listen to the spindles, idlers look and feel good no slop. Belt was new at 4 pm today and still jumped after I hit the pto to run it.
  3. T

    John Deere 112 mower deck

    No twist in belt. And the tightner moves freely(almost got my fingers). I used a drill on one of the spindles and ran both ways with out jumping off the pullys.
  4. T

    John Deere 112 mower deck

    I have a late 60"s 112 and can not keep the belt that drives the blades on. If I drive it with a socket on the blade spindle it stays on as soon as I mount the deck and power it it pops off. Any ideas the idler pullys seem fine and the spindles seem tight.
  5. T

    oliver 77 row crop

    Sent e-mail not sure it we t thru. You can e-mail me at tom_mitchell_48809at yahoodotcom you need to change the at and dot
  6. T

    oliver 77 row crop

    Mid Michigan
  7. T

    oliver 77 row crop

    Could someone give me an idea what it is worth 6 cylinder 6 volt 6 speed trans. Does not run but not frozen . Would need tune up and carb kit to get it running, plus tires.
  8. T

    1960- 630

    gas, narrow, has fenders, 3point
  9. T

    1960- 630

    What is a running 1960 630 worth in mich. tin is fair,rear tires are fair runs good.
  10. T

    John Deere air compressor

    What is the part number for the cup on the bottom of the piston. I found 2 and tjey both leek out he top.
  11. T

    Tractor salvage yards in Michigan?

    roeters in grant noth of grand rapids 231-834-7888 get part for myfarmall there but they have a lot of other brands there.
  12. T

    Farmall A

    Went both ways. Threaded the rod twords the back of the tractor and the clutch would not disingage reversed it came up on the end of the rod back to square one.
  13. T

    Farmall A

    The pedale is bottomed out and just releases the clutch at full travel
  14. T

    Farmall A

    The pedale travel is long tried to adjust and I am at the end of my adjusting rod. When I looked at the throw out bering there is about a 1/2 inch between the clutch and fingers. Is there some thing I am missing.
  15. T

    Farmall A

    On the Farmall A clutch the fingers how close should they be to the throw out berring? Can they be adjusted in place or do I have to split the tractor.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top