(800) 853-2651
SHOP NOW

Recent content by TiredA

Yesterday's Tractor Forums
  1. T

    heisler head

    I do on my late A. Running G pistons in the PB. Likes good gas, lots of it! LOL
  2. T

    John Deere B 1948 Mild Pulling Parts Wanted

    I have a bare Heisler head for a late B I would part with. South central MN.
  3. T

    9 bolt 38 wheels

    Try Wold in St Ansgar.
  4. T

    JD 4520

    Not to be contrary or argumentative Larry. But a 50-55 series MFWD set for 30" rows isn"t exactly handy either. A 4520 would turn around in half the distance.
  5. T

    Kiester Mn Show Pic 2013

    LOL! It usually started about a day or two before the upcoming pull. We would have our tractors weighted to pull a particular class, and our dad's would set up a practice pull on the field road. Dad would get a bucket full of dirt with our 4430, throw a chain under the bucket, hook the tractors...
  6. T

    Kiester Mn Show Pic 2013

    My dad and Dale were great friends, and I can"t remember when I didn"t know the Yonkeys. They always had Cases, we had Deeres. It caused some friendly rivalries between Dale"s son, Mike, and my brothers and I. We settled it with a log chain, or a plow, and on the pulling track a few times. I am...
  7. T

    out ragious Deere dealer prices

    A&I is junk.
  8. T

    So what was the worst advice you ever heard or was given.

    That sounds like advice I'd give myself! I'm the guy who usually tries "the other side of the track" It has worked.....a FEW times.
  9. T

    Model A Head Mods

    I"m afraid milling the head isn"t going to gain you enough Hp to notice. I"d swap the first reduction gears out of the "52 to slow it down a bit....then do the head mods. I pulled a "48 for a while and had the same problem as you. So, I traded for a "51 with the lower gears. Then I built the...
  10. T

    power

    If you are on the wheelie bars, you missed the setup.
  11. T

    6 row narrow on JD 4400 combine

    Jugs, how you doin? Harvest is creeping up on us in Southern MN. You got an extra 643 head?
  12. T

    4020 rear tires

    If it aint a firestone it aint much!
  13. T

    Mapleton, MN pull

    Yes there is, so it will probably rain.
  14. T

    Hotfoot II pulling schedule

    712-284-1725
  15. T

    TiredA, I finally got a good look @ the old Dodge.

    jal-Thanks for looking. The hunt continues. You aren't creeped out being on the "Deere" board?
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top