(800) 853-2651
SHOP NOW

Recent content by TKelley

Yesterday's Tractor Forums
  1. T

    Tandem Plow Hitch

    I wont have trouble pulling them, she weights 22,000 and has well over 225 hp. The 5 bottoms I have I pull with my 650 diesel in 3rd gear on land hitch.
  2. T

    Tandem Plow Hitch

    I know I can make one, I have a pic on my phone from the video I have, I will also be pulling 2 model 700 plows one 5 bottom in front and 1 6 bottom in rear all with my 4366. Video shows that it looks like a wagon pipe center pole that is adjustable.
  3. T

    Tandem Plow Hitch

    I am in search of an International plow hitch that hooked a second 5 or 6 bottom plow directly to tractor hitch with a bar that hooked to rear of first plow to hold the hitch off ground and drawbar of rear plow hooked to that end, not in need of hoses to rear can install new ones. Going to hook...
  4. T

    National IH Collectors Auction Oct. 14 and 15 in Minnesota

    Hi Brian, will be at the auction on fri. and sat. till 1 or 2 then heading west hope to see you there
  5. T

    Disc Brakes

    Hi Al, how are your brakes operating, grabby or just not enough drag, I have a milling machine and work on lots of them. I have done a lot of mine still have a couple more to go. Call me 412-812-5632 if you need a hand with them.
  6. T

    Narrow Tread -Regular

    They made them even later than that, I own one 136325, also has a narrow tread, three speed, and open gears but an updraft carb. and manifold. Know of another 4 digits newer than mine in Ohio
  7. T

    How long are your splines lasting?

    Every time we change a clutch in a live pto tractor we change the pressure plate with clutch and we also change the drive gear that goes into pressure plate will a lot of use a little bit of wear on the gear will cause the pressure plate to wear rapidly.
  8. T

    Farmall A clutch problems

    Not too difficult to split tractor. Noise could be coupler that is located just in front of transmission. Block engine on each side of front axle to keep from rocking either direction. Block engine under bell housing and also block rear end just behind four bolts to split. Acouple of levers and...
  9. T

    Anybody at/go to RPRU this year? If so, your thoughts?

    Just got back from the round-up.The F-12 wide front and F-14 with 40" rubber were in the building at the end of the old tractor row. I can't say any bad about the show because for me it is all about the people you meet, the new and the old. Great to finally meet in person Nebraska Kirk, Buddy...
  10. T

    IHC Winter Convention in Michigan City IN 5, 6 and 7

    Open to the public, will be parts and all kinds of venders, chapter tables will be selling there items and also have some seminars on tractor related things. I am leaving this morning about 6.5 hours from my place. it's a great time .
  11. T

    1935 farmall F-12 questions and help

    Get a really thin chisel or screwdriver and try starting it right at those pins. Mine was so bad I placed a little heat on pins with torch and let cool plus lots of blaster
  12. T

    F series tractors

    I happen to love the old F series myself Jim. I have F-12,F-14,F-20,F-30 not done yet, Farmall narrow tread, and a 22-36, next purchase will be Industrial 20 with a grader on it.
  13. T

    McMormick Deering Tractor

    Looks like an Industrial 20. Had same motor as the 10-20. Used a lot of these in mills and other applications such as road grader power. Could be a 15-30 look under fuel tank behind engine for serial tag. Tag could be on cab like the Industrial 20 that I know of
  14. T

    Industerial IHC

    A picture would help greatly. I have an International AI. Not familiar with that number. Find a number on the engine block that may help with what engine is in it.
  15. T

    Countdown To Red Power Roundup 2015

    Cowman, met you at Red Power at Lima, OH. I had the 400 LP draggin around the track what an awesome time that was. Bringing a 36' f-12 gray with factory wide front, 38' f-14 40 inch rear rubber, cast wheels, my grandfather bought it new, and maybe my 41' AI that I'm tryin to finish right now...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top