Recent content by TKemp

  1. T

    Ford 6610 flywheel

    Did that but you have to also make sure timing mark on flywheel is set with injector timing mark. Unfortunately on this tractor there was no 23 degree BTDC on flywheel so we were kind of stabbing in the dark. Thanks though.
  2. T

    Ford 6610 flywheel

    Did that but you have to also make sure timing mark on flywheel is set with injector timing mark. Unfortunately on this tractor there was no 23 degree BTDC on flywheel so we were kind of stabbing in the dark.
  3. T

    Ford 6610 flywheel

    Thanks again I didn't think so but never hurts to ask.
  4. T

    Ford 6610 flywheel

    Thanks will try that. The two grooves on injector were shown before I aligned them. Is there any movement of injector externally to fine tune it does not seem to me there is? In line Minimec.
  5. T

    Ford 6610 flywheel

    Has anyone ever overhauled older Ford 6610 diesel and found different marks on flywheel for timing injector? There is no 23 degree mark on flywheel to use for timing. TDC compression stroke number one cylinder 0 degree on flywheel. Reversing engine by hand a filed mark on flywheel lined up on...
  6. T

    timing 6610 diesel

    Still need help if you can. I sent you a reply Sunday evening but don't know if you received it? I got it running but I have looked and there is no 23 degree mark on flywheel.
  7. T

    timing 6610 diesel

    Need help with timing of my Ford 6610 diesel, 1982 model. Injector pump was pulled when head and block sent to machine shop for work. Reinstalled crank, cam and injector by aligning marks with idler gear on reassembly. There is a mark on the injector pump and the injector pump gear that also...
  8. T

    Input Shaft Tube on 6610 Diesel

    I ordered a replacement to compare with. Recommendation from shop foreman at Ford/New Holland dealer is to replace. Hard to see wear in picture but if you start by looking inside large end the first machine surface which looks to be about 1/4 inch wide is supposed to be wider, the next area is...
  9. T

    Input Shaft Tube on 6610 Diesel

    Already ordered replacement housing.
  10. T

    Input Shaft Tube on 6610 Diesel

    No, standard 8 forward 2 reverse. Shop foreman at Ford Tractor said need to replace.
  11. T

    Input Shaft Tube on 6610 Diesel

    Replacing seal on Input Shaft. On the end where seal fits and the same end that bolts up to the transmission housing I need to know what the surface is suppose to look like. The shaft slips over the main input power shaft and fits up against a bearing inside the transmission housing. There is...
  12. T

    JD Gator 825i Drive belt repair

    Need help replacing drive belt on JD Gator 825i. I don't have special tool to pop clutch disc has anyone made their own and had success. Dealer is three weeks out for repair can't wait that long. While trying to break clutch disc loose do you need a span wrench to hold clutch disc?
  13. T

    Tach drive on 6610

    What holds tach gear drive assembly in block? I didn't pull tack assembly off so I am at a loss here trying to figure out what holds it. This is on an 82 model diesel 268cu in four cylinder.
  14. T

    Tach drive on 6610

    Need help putting tach drive back together on 6610 Ford diesel.
  15. T

    Replace clutch or not

    The machine shop doing my head and checking cylinders said they did the engine overhaul previously putting in the new cylinder sleeves and such. They are reputable good firm that was the good thing previous owner did maintenance was not so good and why we are here again. I mention that because...
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top