(800) 853-2651
SHOP NOW

Recent content by tomdowling

Yesterday's Tractor Forums
  1. T

    Green Acres

    maybe they rode the cannonball to mr druckers on their way to petticoat junction for some pie.
  2. T

    3 pt lift

    yes
  3. T

    560 gas

    I tend to think he's overstating it. You might need to perform a first person visual on that claim.
  4. T

    asking for a guess??

    I'd guess they are 264 cubic inch now - 4 inch - hp ?
  5. T

    Need 300 Farmall Help

    try wengers of myerstown
  6. T

    Maggie is a new mom!

    Black-capped chickadee
  7. T

    locking gas cap 504U

    back in the 70's i had that problem too with vanishing gas---break a few strait blade razors in half and super glue them to the lip of the cap--- my gas stopped disappearing and there was a couple neighborhood teens who kept their hands in their pockets until they healed. mean but effective.
  8. T

    706 will not run at high rpm

    2nd what Bob said you have a fuel issue---you're getting enough to run at low throttle and dies when you open up throttle. Try choking it when she starts to die to see if it will throttle up. A partially clogged orifice in the carb could be the problem. Did you run a small wire through all the...
  9. T

    sharpening bush hog blades

    I know that if you continue to sharpen your blades without balancing them it will be sooner rather than later and you'll be replacing seals and bearings--- take the blades off sharpen them but make sure each pair weighs the same to prolong the seal and bearing life. Also a sharp blade takes less...
  10. T

    Hydraulic 'float' for M hydraulics

    I think you need a valve with a float position.
  11. T

    Cowman

    if what is said on bob's post is true then it's good he's gone.
  12. T

    300u tach

    seems strange tach reads zero hours
  13. T

    300U gauge hookup

    hooks up by the distributor
  14. T

    How to read the Serial Number

    squirt a little oil in the cylinders before you crank the engine over
  15. T

    Mowing with a 450 D

    I have a 15 ft bush hog brand flex wing cutter that I pull with my 400 (4 1/8 pistons) I have no problem cutting in 4th if it's not too tall (sharp blades take less hp) Plus you have lower gears and a T/A if it's real thick and tall. I realize I'm pushing the limit pulling a mower that's...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top