(800) 853-2651
SHOP NOW

Recent content by tomnwoh

Yesterday's Tractor Forums
  1. T

    Float ride set rebuild

    Steiner has a video describing the rebuild step by step. Recommend watching it
  2. T

    630 Power Steering Issues

    Use a press, just did one . Don't push on shaft .
  3. T

    Jd 50 radiator restoration

    Heat all the bolts first,use new bolts
  4. T

    JD 7520 Sound-Gard Hydraulic Issue Fixed, Finished Photos

    That is unbelievable, beautiful job ,my compliments
  5. T

    Pics of 7520 Sound-Gard Project

    That is a one of a kind ,beautiful job. My compliments
  6. T

    69 Plymouth

    Does it have a clutch pedal?
  7. T

    School me on cover crops

    I was doing a lot of covers. Went well until the voles showed up. I have stopped covers and the voles are gone .
  8. T

    Decal removal

    I acid dip a lot of sheet metal . Works excellent. There is a good one in Sandusky ,Oh
  9. T

    John deere 50 brake seized

    Pull the whole assembly. Take the nut off. Lay a piece of hard wood on a concrete floor . Drop the assembly on the stud till it breaks loose. Pull everything apart and clean and lubricate. Replace if needed. You will then have working and adjustable brakes for a long time
  10. T

    Loose wheel on 620

    You have a worn wedge. Check the wedge that fits in the keyway on the axle. Replaced a few
  11. T

    Value of a New Idea loader

    Interested in talking with you . Replied on Ag Talk
  12. T

    3020 steering motor repair

    Just did one. Front axle must be removed . You do not remove side rails, just loosen bolts on both sides. I removed the fuel tank , make removal easier. A forklift or something to support on wheels to slide to the unit out the front. Leave the front cast piece on and remove with unit...
  13. T

    3010 oil leak,steering motor

    I am just finishing a 3020. I replaced both bearings and the seal.just what I found, remove the tank , remove the front axle and slide the unit out together with the front cast piece
  14. T

    Poll or old members

    Check everyday
  15. T

    4240 3 point

    Just did my 4040 last week . Rebuilt the 3pt controls , needle valves were bad . Pull the plug under the right side remote . Take a long extension and tape it , 9/16, push in, it's spring loaded and make small increment adjustments. Recommend a 2nd person , one cab and one adjusting. Works...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top