(800) 853-2651
SHOP NOW

Recent content by troy25

Yesterday's Tractor Forums
  1. T

    Detroit 3-53 help? Advice?

    It's been running, but since iv owned it it's never r illy raved up high, I have a lot of play in the fork that attaches to the throttle rod and the govner rod..and if I set the buffer screw per book, 5/8 From locknut it wants to stay raved up and not idle down... also. When setting gap, book...
  2. T

    Detroit 3-53 help? Advice?

    Yes, revs up great. Fast also by hand
  3. T

    Detroit 3-53 help? Advice?

    The shut down is working and is there if needed, don't seems like anything is sticking, just this govner is eather wore out or not adjusted right
  4. T

    Detroit 3-53 help? Advice?

    Blower fed
  5. T

    Detroit 3-53 help? Advice?

    Got a old skidder with a 3-53, previous owner said he had it rebuilt and re man injectors..it runs but just don't rev up hardly at all.. so if downloaded manuals and got the tool, adjusted valves, adjusted injectors...s50 injectors btw..prev owner said there bigger injectoes... any...
  6. T

    case 450b

    Anyone ever pUT a winch on one of these, I'm told there is a pro shaft in the back, but was curious about what braket u need to install..photo of some would be great to or if u have done some please chime in
  7. T

    Allis winch

    Anyone know about a ac 400 winch and any info or shop manuals for a h3 I can't find much info at all on these
  8. T

    h3 Allis chalmers and ac 400 winch

    Anyone have any info on the main clutch and reverser, I think my reverser is slipping, and also who made the ac 400 winch on these machine...I need to know we're to fill.with oil and the control parts of this unit.. also looking for a motor for.the dozer..it's gas
  9. T

    540 to 1000 pto

    From searching for 2 days about it now., seems as if your all right..it just un bolts and a new one bolts in aND pushes a pin in...I'll see today...I only need it for my fl20 rhino bush hog. It's got a 1000 rpm spline shaft...Thanks to everone
  10. T

    540 to 1000 pto

    I got a 93 fiat f110.. it has a 540 pto on it now and the shaft is one that's held on with 3 bolts.. my question is how do I change to to 1000rpm for my bushhog just in bolt the 3 bolts and get a 1000 rpm shaft or is there a leaver I gotta change or what? Anyone know
  11. T

    Tire Changing

    we always use dawn dish soap for semi tires loader tires and tractor tires, we rub it on the beed by had with a rag and on she goes,
  12. T

    120/208 three phase

    now that u have broke it down I see, its my grampa shop nd his big three pahse welder took a crap so I bought us a new to me used welder grampa hooked it up and it powers up but not stong, like it don't have enough power, and am clueless on why it don't seem to work until I seen the back door...
  13. T

    120/208 three phase

    so my system is 240v three phase.......... if so I need to change my welder around because its set up on 480v three phase
  14. T

    120/208 three phase

    ok guys got a new to me welder, its a miller mp-65e witch is a three phase machine, now when going to wire it up im confused, on the back it has tabs to move around that u can make it 240v three phase or 480v three phase, its set up for 480v three phase now, but I can rember what my shop has, to...
  15. T

    550 hesston roller

    got a new to me 550 Hesston roller.. after do lots of work to get it rolling again there one last problem I noticed when using it for the first time today.. sometimes the hay is hard to start or it don't seem to suck n very well.. I know this has the starter flaps on the start roller and they...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top