(800) 853-2651
SHOP NOW

Recent content by troycat

Yesterday's Tractor Forums
  1. T

    Losing power under load

    Fuel flow is fine, Mowed for a short while last night and tractor ran good. So something with the spark. I'm going to get some of those fancy points you guys talk about (although the places I was at last night would have to order them in) and some new plugs. Thanks guys for all the help...
  2. T

    Losing power under load

    Both actually
  3. T

    Losing power under load

    Still A 6 volt system, I did check for fuel at the line, I will check at the bottom of carb tonight and check the spark. I wouldn't be suprized either if the points are bad already. Any idea how to seal the breather tube at the engine block? Thanks!
  4. T

    Losing power under load

    Mowing with my 1940 9N Front Mount, going through tall grass the motor seems to pop or sputter like its running out of gas, when I get through or lift the deck the rpm"s come up and sounds fine. Checked for fuel flow at carb, seemed good. New TSC Coil & points a year ago. Tractor had been...
  5. T

    9n oil line leaking

    Are you saying take it into a parts store and have them make one?
  6. T

    9n oil line leaking

    Where is the best place to buy the oil line from pressure gauge to junction block? I did't see in on the YT site. Thanks
  7. T

    9N won't restart after it runs a while

    Recently split my '40 9n To replace clutch. Decided to replace wiring harness and Ballast resistor while I had the wires off. Runs good but dosn't want to restart after running awhile until it cools off. Any Ideas? Thanks!
  8. T

    9N Tractor Split Clutch Replacement

    End up using wet newspaper instead of grease. I was pleasently surprized that it worked. Thanks
  9. T

    9N Tractor Split Clutch Replacement

    OK, I got the pilot bearing out using wet newspaper and a socket. End up being a brass bushing. Still need help removing the throw out bearing from the bearing holder. Seems to be some sort of bearing cover on backside of bearing. Any ideas?
  10. T

    9N Tractor Split Clutch Replacement

    So the bearing holder has to come out? Just remove the springs? Thanks for the Help
  11. T

    9N Tractor Split Clutch Replacement

    Clutch went bad last week while mowing, by bad I mean in pieces. Anyhow tractor is split and waiting on clutch kit. My question is how do you remove the pilot bearing and throw out bearing. I have the transmission with the step up. Any other advise would be greatly appreciated. Thanks! Troy
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top