(800) 853-2651
SHOP NOW

Recent content by TutorN1

Yesterday's Tractor Forums
  1. T

    Ford 4000 shutting off?

    Fuel filters are brand new put them on when swapped the injector pump.
  2. T

    Ford 4000 shutting off?

    Got a 65-67 4000 that runs great at an idle, but once you put a disk or blade on it and start running it it shuts down. Not running hard rpm was around 18-20. Can let it sit over night and will crank back up on issue. Has a new CAV injected pump, and a fresh oil bath in the air filter.
  3. T

    Throttle linkage question on 4000 Ford

    Thanks for the info, and there wasn?t anything there that resembled that. I?ll see about getting one on order, or may try making one for the time being.
  4. T

    Throttle linkage question on 4000 Ford

    Ah, took the nut, and spring off to take the tank off the other day. There wasn?t a washer. Like i said, there was several parts off before I got it. I got a tractor, and a box smh
  5. T

    Throttle linkage question on 4000 Ford

    I?m looking forward to hearing it run, and see just how much black smoke it rolls.
  6. T

    Throttle linkage question on 4000 Ford

    Sorry it going to be the 3 cylinder diesel. So it?s the 65-75
  7. T

    Throttle linkage question on 4000 Ford

    I?m in the process of getting a 4000 back running. Issue I?ve got is the last owner had started taking (or trying to) apart the tractor. The throttle leaver works, but it goes back to idle position when you let go of it. What is it that keeps it in the throttle position you set it at? I do...
  8. T

    Ford 4000 Drawbar

    Got just a simple one made this morning, material going to run about 10-15 bucks, and that?s with a new pin.
  9. T

    Ford 4000 Drawbar

    I?m new to these tractors, have been around JD up till now. Wanting to say this one is a 65 or newer from what info I?ve see so far.
  10. T

    Ford 4000 Drawbar

    I was wondering if anyone had a good measurement or print for a draw bar to fit my Ford 4000 tractor. I work in a machine shop and was going to try and just build my own from scratch. Only thing is I?d need something to go by, they tractor I got is lacking one. It does have the mount for one...
  11. T

    Ford 4000 Drawbar

    I was wondering if anyone had a good measurement or print for a draw bar to fit my Ford 4000 tractor. I work in a machine shop and was going to try and just build my own from scratch. Only thing is I?d need something to go by, they tractor I got is lacking one. It does have the mount for one...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top