-
Kubota hydraulic shuttle...in M series. I never touch the clutch pedal typing bales, bump shuttle in neutral, tie bale, eject, bump... -
Tx Jim replied to the thread JD 350 hay rake - need a new tooth pipe.The JD model 350 ,640 or 650 hay rakes do not share same part #s for tooth pipes
-
Tx Jim replied to the thread JD 535 netwrap problem.You're welcome Please provide more information. Do netwrap feed rollers rotate when tying cycle is activated. If net isn't wrapping on...
-
-
That looks like an ordinary cup type core plug. You should be able to find one in most any auto parts store.
-
If you pull the plug and you find heavy gear oil in the pto clutch the seal is bad between the pto housing and transmission. You will...
-
Tx Jim replied to the thread 1969 jd400 tlb no brakes.Sorry I overlooked you plugged off lines leading to rear brake pistons. Does fluid return to reverser control valve if both pedals are...
-
Tx Jim replied to the thread John Deere 50 PTO Clutch slipping.I agree to attempt adjusting pto clutch by removing round plug on RH side of housing. Type adjusting nut determined by tractor serial #.
-
-
PTO clutch is adjustable. Take a look to see if there is room to adjust tighter or if clutch is wore out. Not difficult to adjust...
-
If you don’t know where the screw is, that lack of knowledge tells me you should probably not be messing with it. Just my personal...
-
Tx Jim replied to the thread 1974 JD 2030 Diesel.Is electric solenoid on inj pump being energized when ign switch is in on position? Is fuel tank venting? Is fuel return line open to...
-
Tx Jim replied to the thread 1969 jd400 tlb no brakes.Sounds as if rear axle brake piston seals have failed. Did you bleed brakes with engine operating?
-
Tx Jim replied to the thread 1969 jd400 tlb no brakes.Sounds as if one or more check valves in brake valve housing has failed. Common check valve to give problems is part # AT184434. Which...
-
-
Tx Jim replied to the thread 2950 trans clutch slipping.I'm fairly confident without having access to a 2950 tech manual to confirm that a 2950 tractor with a cab can be split between engine &...
-
Welcome to the forums. Scrapcan was last seen in October of 2022. Best you start a thread of your own, describe your tractor, its...
-
Tx Jim replied to the thread Deere 35 Series round balers.I'm not sure I should be referred to a a rd baler expert but I demonstrated/delivered new JD 410/510 rd balers in '77 & owned 6...
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy