-
V
4600 Hydraulic problem. Bucket won't lift.
As soundguy said, are your levels OK? The 4600 has separate oil for the transmisjon and hydraulics. Was fooled by this running my grandfathers 4600, which also wouldn't lift when pointing uphill. -
V
1988 Ford 3910 PTO Feather Engage Adjustment
http://www.yesterdaystractors.com/cgi-bin/viewit.cgi?bd=ford&th=555129 -
V
3550 Axle seals
http://forums.yesterdaystractors.com/viewtopic.php?t=804242&highlight= -
V
4610 fuel leak
Common fault on these pumps. The o-ring around the throttle shaft going into the pump is worn. You can find some info here: http://forums.yesterdaystractors.com/viewtopic.php?t=505083 http://www.yesterdaystractors.com/cgi-bin/viewit.cgi?bd=ford&th=424639 Had the same leak on mine, got a... -
V
6600 Ford axle seal
I have posted some pictures of the process for a 4110 in a previous post. I think it is similar for the 6600. http://forums.yesterdaystractors.com/viewtopic.php?t=804242&highlight= -
V
641 Power Steering Conundrum
That crack sure looks like a cold shut in the casting (the metal was too coold when poured) -
V
Ford 7610 1986 Front Axle Schindler 627 166 SF2
I will reply in norwegian, sorry guys. Hei Knotten. Schindler akselen er rimelig ukurante greier. Ikkje mykje hjelp å hente her da den er praktisk talt ukjent i USA. Sjekk ut den svenske sida maskinisten net, (kan ikkje legge inn full addresse her) Der er det meir info å hente, og du kan... -
V
Thermostart
I would say it would be worth the trouble. Heating the air entering the engine makes a big difference. On my air compressor with a six-cyl ford diesel engine I haven't got a thermostart, but I disconnect the air-filter and direct the flame of a propane burner into the intake manifoild when I... -
V
3910 timing
According to my manual, that is correct. Line the number up with the camshaft drive timing mark. -
V
I really Messed up! Any Ideas?
Stupid question, but the 10 you can't get in aren't the ones that go into the tubes painted blue in the pic? -
V
Ford 4610 Rear Axle Seal advice....
When I changed the seal on my '83 4110 this summer, I applied a smear of sealant to the outside diameter of the axle housing before sliding on the seal retainer. I then wedged some pieces of wood between the axle flange and the seal retainer to compress the rubber seal between the retainer and... -
V
7710 heater
On my '83 4110 I had a similar problem. Turned out to be a defective o-ring in the heater valve.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy