(800) 853-2651
SHOP NOW

Recent content by V8Super88

Yesterday's Tractor Forums
  1. V

    tractor pulls

    More info on these pulls would be nice.
  2. V

    Dctpa

    Sounds like we are going to have good weather sat. high near 50 degrees and partly sunny.
  3. V

    DCTPA

    I just talked to Loyd about this and he said we are going to pull all the non-cuts first, light to heavy. Then we are going to alternate the top-cuts and full-cuts, light to heavy. So it will be 3500, 4500, 5500, 6500 & 7500 non-cut. Then 3500 top-cuts, 4500 full-cuts and so on.
  4. V

    Remnder for up coming pull

    Who is planning on attending?
  5. V

    Eaton Ohio Pull

    Try agian
  6. V

    Eaton Ohio Pull

    Here is the flier for the Darke County Tractor pullers
  7. V

    Eaton, Ohio pull

    www.dctpa.com Watch the web site all the info will be on it
  8. V

    Super 88 gear

    Anyone have a 47 tooth ring gear that was mated to a 12 tooth pinion that they want to sell.
  9. V

    Super 88 gears

    The too gear has 1K609A on it. The bottom gear has K1023 on it. Thanks
  10. V

    Super 88 gears

    I"m looking for the 3rd gears for a super 88. Can anyone suggest a good place to call or look?
  11. V

    Super 88 Manual

    What holds the middle shaft with the gears. I got both nuts off and it won't come out. I haven't got agressive with it because I didn't want to mess up the bearings. I pull this tractor in the hotrod class, it has a small block chevy motor with an automatic. This is the first problem I've...
  12. V

    Super 88 Manual

    Would anyone have or know where I can down load a service manual, need to do some work in the rearend and transmission. Thanks
  13. V

    V8 Pullers Custom/Simpons Question/Opinions needed

    Here in western ohio all the clubs run a small block rule, I think all or most of them are 410 cubes with a rebuild rule. The M will work fine several of them running has well as 560's, supper 88's cockshutts, massey 44's and a minnie mo, sure they break once in a while but so do the componant...
  14. V

    Super 88

    Is there any other trans gears that can be put in to slow down a gear or gears. I want to lower my final ratio. I know I can change ring & pinion just looking for options. Thanks
  15. V

    putting v8 in oliver

    You need to can the factory tub and build a frame. Most places want sfi approved cluthes flywheels and bellhousings. Find a local machine shop to make a shaft to fit the clutch and the gear on the tractor input shaft and use the same chain it has now. I run an automatic in mine and had the yoke...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top