(800) 853-2651
SHOP NOW

Recent content by Vann

Yesterday's Tractor Forums
  1. V

    MF35 wiring problem

    Thanks for the reply. As you noted, I added the fuse when I rewired the tractor. I assumed that a fuse is always a good idea for protection. maybe that's not a good idea?? I will try a 20 amp fuse and see if that holds. Again thanks Vann
  2. V

    MF35 wiring problem

    I have rewired my MF35 per the enclosed diagram. I am having a problem with the 15 amp fuse blowing occasionally. I can use the tractor several times and all seems fine. However, next time I try, the tractor is dead-blown fuse. Any ideas would be greatly appreciated Thanks Vann [/img]...
  3. V

    MF202 post hole digger recommendations

    I used a pto driven post hole digger to construct my pole barn using old telephone poles. the auger was 10" in diameter and my tractor is a MF35. The first hole taught me a lot. I dug it as deep as I wanted, then tried to pull the auger up out of the ground. It didn't pull up-but the front...
  4. V

    Regulator Wiring

    I recently rewired my 1963 MF35. I also purchased a new regulator with the same terminals. Mine is a gas engine and 12v negative ground. Here is how I wired mine. I take no responsibility for your work-do what you think is right. I am not a professional.. From the regulator The F goes to the...
  5. V

    engine speed PTO not working

    thank you for all of the pictures and advice. I'm a little confused-are you thinking that the hydraulic pump needs to be replaced? I will check and see if the lever has been moved, but I don't think it would work for ground speed if it had moved?? From the pictures and notes, it seems that...
  6. V

    engine speed PTO not working

    I changed the oil recently-I added 8 gallons-do you have any idea how much I need to drain to get below the level of the cover? Where can I see a picture of what's behind the cover. I have looked at all of my manuals and they don't have that picture. Thank you Vann
  7. V

    engine speed PTO not working

    The last time I used it, the gears would grind when I engaged the engine speed PTO. But it engaged and worked. This time, I would move the engine speed lever up while having the clutch fully engaged. Nothing-no grinding, no shaft movement, no noise or resistance. I engaged the clutch fully and...
  8. V

    engine speed PTO not working

    I have a 1963 MF35 gasser. This morning, I was going to use my bush hog and cut my power line. The engine speed PTO would not engage. I tried several times, engaging, disengaging the clutch and PTO with no change. I tried going from enginee to ground and back. turned the tractor off, back on...
  9. V

    MF35 blowing fuses

    I just rewired my 1963 MF 35 using the wiring diagram found on the massey enthusiasts.org website. I installed new voltage regulator, ignition switch and starter button. I added an inline fuse between the ignition switch terminal and the voltage regulator "L" terminal. Now the tractor is...
  10. V

    Neutral Safety Switch Connector

    I know this is an old post-maybe you already fixed the problem.I rewired my '63 MF 35 and replaced the neutral switch in the process. I also could not find the appropriate wire ends and ended up just splicing new wiring to the old ends. I left about 2" of the old wires with the specil ends. The...
  11. V

    John Deere 1050 diesel wiring diagram???

    THANK YOU!!This is a great help We have the 1192 manual, but could not find a comphrehensive wiring diagram Maybe it is also missing pages?? Thanks Vann
  12. V

    John deere 1050 diesel wiring diagram???

    Thank you for your help. I don't own the tractor or have the manual-I'm trying to help a friend who actually owns the tractor and has the manual. I just completely rewired my 1963 Massey Ferguson 35 and was able to find a complete wiring diagram that included all wiring in one schematic...
  13. V

    John deere 1050 diesel wiring diagram???

    thank you very much for this information- We have the John Deere Technical Manual #1192 from August 1986-it is different , but helpful Thank you Vann
  14. V

    John Deere 1050 diesel wiring diagram???

    does anyone know where I can find a JD 1050 diesel wiring diagram? The "official" shop manual does not have one. Thanks for any help Vann
  15. V

    John deere 1050 diesel wiring diagram???

    Does anyone know where I can find a wiring diagram for a JD 1050 diesel? the "official " shop manual does not include onethanks for any help. Vann
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top