(800) 853-2651
SHOP NOW

Recent content by vista2016

Yesterday's Tractor Forums
  1. G

    Case Davis 30+4 starter

    I have a case davis 30+4 that needs a stater. The starter that came off it was a prestolite mbg 4141 which has 10 teeth. My parts book calls for a Delco Remy 1109424 which has 9 teeth. When I first got it it would crank and run but it got to where it would not start. Any idea? Does it make a...
  2. Tim in New York

    Kubota Recovery Tank

    I need to add some anti-freeze to my B2620. The radiator is full, the recovery tank almost empty, and I need to put in some pure antifreeze to bump down the freeze point. But I don't see how to get the lid off the tank. It appears that it should just lift off, but it won't budget. And I don't...
  3. V

    Hydraulic drift problem

    Thanks for the replies guys. Cylinders are off and going to the shop tomorrow. I'll let you know.
  4. V

    Hydraulic drift problem

    Thanks Matt. I agree, that's the only thing left to replace at this point. Just seems crazythat both cylinders would go bad at close to the same time. I would think if it was only one cylinder then I wouldn't notice the problem because the other cylinder would be doing all the work but I could...
  5. V

    Hydraulic drift problem

    I need some hydraulic help. I've got a Deere 440ICD with simple outside mount 602 blade. Power up/down, manual angle. I've been fighting a problem where the blade won't stay up. It started as a slow drift but now it's to the point where it goes down so fast now that I have to hold the valve so...
  6. V

    What's power pack for on G1000?

    Before you go replacing it you should check to make sure it's grounded. You said it did work and you were in there messing around, seems slightly unlikely that just bumping it or something would have made it go bad. You may have loosened it up some and now it doesn't have a good ground. Also, I...
  7. V

    Minneapolis-Moline G-1000

    X2 on the original alternator mounting. $1,200 isn't bad. It's not a Vista, so top dollar fixed up you might get $6 or $7k. They do have a lot of power, but also a lot to be desired. It depends on how much you're going to use it and what your land is like. Transmission is not synchronized at...
  8. V

    Who knows their NH Square Balers?

    I understand wanting a backup baler. We've been using a 273 for a few years, baler didn't miss and was reliable however it was getting worn and didn't make nice consistent bales. We found a 315 for a decent price, but it didn't work out as well as we'd hoped. The hydraulic tensioner had a little...
  9. V

    OT: Self Driving Cadillacs - Yikes!

    I've got to admit, some of the arguments in this thread are funny. You truly think that if they can develop a car to drive itself, follow lane markers, etc. that they would actually design the car to slow to a stop in the MIDDLE of the highway instead of following the lane marker and pulling off...
  10. V

    Painting outside

    For future knowledge, if you're quick enough you can take a piece of masking tape and usually get the bugs/dirt out. You have to do it when the paint is still very fresh and wet. The wet paint will fill the spot right in and you'll never see it. Done it many times because I usually paint outside...
  11. V

    1010 diesel crawler

    Typically the industrial ones are yellow. Ag ones usually didn't have any blade or loader either. More than likely cracked cylinder liner than a bad head gaskets. Min. $700 for a new deck plate, if Deere still has any left. I thought when we bought ours a few years ago jdparts said there were...
  12. V

    Sand Blasting tank......

    My brother bought that same thing and I wouldn't waste your money on it unless you want to do a little upgrading right out of the box. I think the issue is the plumbing size of the discharge at the bottom. We had awful issues with the sand continually plugging down there. I think it's 1/4 pipe...
  13. V

    The lonnnnng sloooow hay harvest

    Long slow harvest for sure. We just finished the first field of 2nd cut today. Yield seemed a little low. 1st cut took forever to get in, couldn't catch more then 3 days of dry weather in a row to save our lives. Almost everyone's corn here is tassled already. Been really wet this year. Tough...
  14. V

    JD 1010 Crawler

    Good luck with it. Gas or Diesel? They're decent machines when running. If not, then hopefully you have deep pockets. Early or late model? (Shifter on dash)
  15. V

    Knotter Woes Continue

    Are you baling hay or straw? Also, you might try a different twine mainly the old sisel twine. We baled some straw two years ago and it was extremely dry and dusty and our 273 started doing the same things yours is doing, only on one side. We were able to finish the field because it would only...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top