(800) 853-2651
SHOP NOW

Recent content by wels

Yesterday's Tractor Forums
  1. wels

    Kubota L345DT Equivalent Crankshaft

    If you go to Messicks look up the crankshaft for that engine. When you click on the crankshaft, it will tell you all the models that share the same part.
  2. wels

    Brake job M4500

    I replaced the brakes on my M4500 same set up for M4000, M5500, M6500, M7500 also 4050 and some other models.
    • wels
    • Thread
    • Replies: 0
    • Forum: Kubota
  3. wels

    NH 275 baler parts

    Amazon, I figured for how little I use the baler each year they would fine, and they have. I looked up the oem pn then just googled it.
  4. wels

    275 baler pick up cam

    I think from what I read elsewhere, pulling the pickup head is the best way to go. Then check everything while it is out. What is the easiest way to pull the pick up head? I guess I pull the right side wheel, undo the chain. Then one pivot point on each side? Or does the left side...
  5. wels

    275 baler pick up cam

    275 with super sweep On my last bale of the year, my pick up jammed. From what I can see, I believe, the small radius on the pickup cam is warn through. Outside of age, would something else cause this? I was thinking of welding in a patch, any thoughts? Thanks in advance.
  6. wels

    Anybody else dealing with crop

    The littles dont help much, they leave that to their older brother however they like posing for pictures at the end of the day.
  7. wels

    Anybody else dealing with crop

    My first cutting was down to only 55 bales per acre, usually 85/90 bales per acre.
  8. wels

    Liberty Ships

    LST (landing ship, tank). large slow target My grandfather was on LST 820 in the pacific during WWII
  9. wels

    3pt Hay Rake Advice

    I use a 6 bar Ferguson rake like the ones you have pictured, it works well and was cheap.
  10. wels

    First time baling

    Im a little embarrassed to share my story but here goes. Late last month for the first time I gave baling a go. I checked all my equipment (Ill get back to that), the weather, and lined up some willing help (and some not so willing help) and set out to make some hay. The hay was looking...
  11. wels

    75 4000su stabilizer bar

    I made my own. Used angle iron and chain. Didnt cost much and works pretty well. https://forums.yesterdaystractors.com/viewtopic.php?t=1345285&highlight=
  12. wels

    International 990 7 foot haybine opinions

    have a 7ft unit with 2 rubber rolls. This was my first year using it. I replaced the chain because it was stretched so much it wouldnt sit down on the big cog. Adjusting the spacing on the rolls is a bit of a pain (need to remove spacer plate). I ran it behind a 4000 SU on hilly ground...
  13. wels

    Ford 4000 PS filter

    This is what use on my 4000 su, Im not sure if the AP is the same.
  14. wels

    Common problem Areas with old balers

    Check the bearings on plunger and finger feed carriage. There can be up to 10 on feed carriage alone and almost that on the plunger. Check carriage bolt heads that are on the inside of bail chamber and chute. Those are things I have found/replaced on my NH baler I m sure you get...
  15. wels

    NH 275 baler repairs and test

    I worked out of D2 (AMO) for 6 years. Now I work for MSC through a private contractor.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top