(800) 853-2651
SHOP NOW

Recent content by willintexas

Yesterday's Tractor Forums
  1. S

    John Deere 318 misses

    I have a John Deere 318 mower that has a weird problem that I can't figure out. The engine runs fine until I engage the electric clutch. Once engaged it will idle fine but miss badly once revved up. I will run fine at high RPM with clutch disengaged. I thought bad clutch and swapped with a known...
  2. G

    1960 Farmall 560 gas tractor problem

    I finished mowing hay with my 1960 Farmall using a New Idea cutditioner. All went well until I went to turn the Pto off. When I disengaged the Pto which did stop, I heard a loud slapping noise from underneath the seat in the hydraulic area I was assuming. Today I took out the hydraulic filter...
  3. W

    vac 14 setting timing

    i need some second thoughts when i set timing on the tractor it rattles from lower end when revving up motor but i can move distributor alittle and it goes away but will not run right what is this from rod bearings and the best way to correct it thanks any help will be great thanks
  4. W

    1948 dc propane value

    i found a dc tricycle front propane with the eagle hitch front tires fair rear 85% tread a little checking on rears person said it has not been started in 2 or 3 years
  5. W

    One way disc tiller in bearing

    give me some info. on this thanks parts depot
  6. W

    fine thread bolts

    go down to a local bolt supply house that deals with bolts only
  7. W

    need 5.00 15 three rib tires used

    need some front tires for my vac i have a 47 vac that has a wagner loader on it wondering if that is right size for the application used would be better i am located in central texas by temple waco area
  8. W

    Any one have DC head in the North Texas area

    hello i was wondering if you any vac parts just checking or any extra dc parts i live in temple area
  9. W

    vac hub clamps needed

    it is a 1947 vac
  10. W

    vac hub clamps needed

    i am looking for a hub clamp that is what i call it it is the square block that goes over the axle four bolt s go through it holds the hub to the axle
  11. W

    ih horse drawn 6 foot planter box

    i need help identifying this old horse drawn grain drill seeing i am going to restore this old grain drill it has ih all over it it has ten disc seed shoots and a ride on seat the seed box is six feet wide the front and back of box has a 1"x12"board witha slide adjustment to set your seed...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top