(800) 853-2651
SHOP NOW

Recent content by Willracin

Yesterday's Tractor Forums
  1. C

    M602 differential

    We got the differential completely disassembled on the tractor and have noticed that the 4 pins that hold the bevel gears in the carrier all have quite a bit of wear. Not where the bushing rides and gear turns, but where it sits in the carrier. Best we can figure the pins must chatter and...
  2. W

    Low Power after 12v Conversion

    Battery has 13.7 volts and it spins the engine very well. I will double check the firing order. The cylinders are numbered from the radiator. Right?
  3. W

    Low Power after 12v Conversion

    Sorry it's a 9n front mount. I am using the originl ballast resistor and a new 12 volt coil. Also if it helps. As a 6 volt the tractor would start in approx 2 -3 seconds and no choke required. Now its 10 seconds using full choke.
  4. W

    Low Power after 12v Conversion

    Sorry it's a 9n front mount. I am using the originl ballast resistor and a new 12 volt coil. Also if it helps. As a 6 volt the tractor would start in approx 2 -3 seconds and no choke required. Now its 10 seconds using full choke.
  5. W

    Low Power after 12v Conversion

    I did the 12v conv. Used an EBAY kit with the original ballast resistor. New Plugs and wires, cap and rotor. Double and triple checked plug gap, point gap and firing order but my tractor is down on power now. Suggestions? also using a new 12v coil.
  6. W

    12 vOLT Conversion 9N

    So I finally completed the 12v conversion. Kit came with one of the white resistors. I opted to follow JMOR's advice and use the factory Ballast Resistor. Tractor of course spins much faster but is slower to start now (Longer elapsed time) than when it was 6v. Also seems down on power, and weak...
  7. W

    A few things for sale

    If no one else wants the floor boards let me know. [email protected]
  8. W

    12 vOLT Conversion 9N

    Thanks so much for your patience everyone. I am using the 12v coil and new resistor. I plan on starting right after work.First question, Do I need any fuses or a junction box since I am not using the original resistor? I still have the single post below the original resistor.
  9. W

    12 vOLT Conversion 9N

    yes typo Should be GM alt. One wire connection. I assume I am to replace the original resistor. I don't really know.As I said the kit came with a Volt coil.
  10. W

    12 vOLT Conversion 9N

    Ebay
  11. W

    12 vOLT Conversion 9N

    Ok So I am doing a 12V conversion on my 1940 9N. I bought a kit and had no problems with the brackets Now the wiring.The kit came with a wiring diagram but I don't seem to understand it. I am not as smart as many on here I guess. Does anyone have the patience to type out the wiring for me to...
  12. W

    9n Wont Turn Over

    Cranked Engine was running fine moved out of barn and switched it off and the trouble began.1940 9N wont turn over or even try to. Things I ve tried so far. Battery is fully charged. (Still orig 6Volt sys and most wiring is stock) Battery Cables replaced. Starter fresh rebuild and works as it...
  13. W

    JD 440 Crawler wont start

    Of course it happened NO WHERE near my house or shop. So I can"t say for sure but I think it is a fire/electrical. Very hard to see the plugs from any position you can activate the starter. Will go back tomorrow with a timing light and check for induction in the wires. NCwayne, will it still...
  14. W

    JD 440 Crawler wont start

    it's gas
  15. W

    JD 440 Crawler wont start

    My JD 440 was running great. Cleaning up some tornado debris. Suddenly it acted just like i had switched it off and now wont start back. Please offer any trouble shooting tips.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top