(800) 853-2651
SHOP NOW

Recent content by willyp

Yesterday's Tractor Forums
  1. W

    wisconsin engine overhaul

    I am overhauling a wisconsin VH4D and it has the babbitt rods on it how do I check to see if I need to take out a shim or just leave them the way they are the bearing surface looks good,also the pistons are not stamped so I guess they are standard and the cylinder wall looks good with no ring...
  2. W

    Where is Rick B ?

    Yes the finished twine after it is whiped off the billhook by the wiper arm and it will hang sometime on the twine finger right in front of the bolt that holds the twine finger on. I went today and adjusted the twine finger to the right a little more until it was in the slot that the needles...
  3. W

    Where is Rick B ?

    Rick,I have a question for you,my NH 570 is breaking knots. It is tying them perfect and coming off the billhook but the twine is hanging on the twinefinger and will break at the knot when the next charge of hay pushes back,when I dont load it up it will work fine,guess it has time to slide off...
  4. W

    NH 570 baler problem

    Yes that is the same as the twine fingers
  5. W

    NH 570 baler problem

    I am having problems with my NH 570,it is tying good but the knots are catching on the twine finger and when a big slug of hay comes out it catches on the twine finger and breaks the twine,when going slow it works fine,the twine fingers are new and a little slack and adjusted correctly. Any...
  6. W

    JD 2640 hydraulics problem

    Found that the stroke control valve under the pump was stuck or stopped up because I backed it out some and ran engine for a minute and then screwed it back in and adjusted it and now it is working fine. Thanks for all the help
  7. W

    JD 2640 hydraulics problem

    On my 2640 tractor the hydraulics have almost quit,the steering and the pto work good but the 3 point is slow and the remotes will only pickup real slow,put a pressure gauge in it and it read 1500 lbs.Changed the filter and cleaned the screen,what and how do I check it further? Thanks
  8. W

    NH 488 haybine

    I have a NH 488 haybine and the left side where the wobble box is, is starting to crack the side of the header. How can I reinforce this side so it will be straight? Has anybody had this trouble? It has been welded up on some of the cracks and now the welds are cracking. Thanks
  9. W

    changing from two batterys too one JD 2640

    Thanks for the good info,I live in east Texas and don't use the tractor much in the winter. I did change the ground cable to ground on the frame instead of on the sheet metal like original.I like the post about using 2 hot cables and grounding to the starter that is a good idea.
  10. W

    changing from two batterys too one JD 2640

    On my JD 2640 will it be alright to do away with the two batteries and put just one with high cranking amps? This is two 12 volts hooked together.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top