Recent content by Wolfram

  1. O

    case 400 front end

    Has anyone removed the front casting, steering sector and pedistal from a 400 and replaced it with a light tube front end? looking for ideas. Thanks
  2. W

    HELP - loader power shaft to front pulley removal

    Hello everyone, Last year we acquired a TO-30 that had a Davis loader attached to it. We finally got the loader off of the little tractor a month ago. The only thing left to remove is a shaft that connected the hydraulic pump of the loader to the front pulley of the tractor. Here is a...
  3. W

    stuck engine oil pressure relief valve

    FWIW, the weird "eye-shaped" bulge on the side of the piston was where the piston was swaged into the oil passage coming from the oil feed line to the pump. No wonder it was tough to get out.
  4. W

    PTO rpm

    Jerry - does the need for an overrunning clutch PTO adaptor apply to belt-driven finish mowers? I can't imagine my Woods 600 mower shoving my TO-30 around once I get this thing back together.
  5. W

    stuck engine oil pressure relief valve

    That worked, Don. I used a 7/16-inch tap, and lightly threaded it in there - just until the tap bit into the oil pressure control piston, maybe a bit more. I was able to pull that thing out of there. The outside of the old piston wasn't smooth. There was a weird eye-shaped bulge on the side...
  6. W

    stuck engine oil pressure relief valve

    engine oil pressure relief valve I got my oil pump out of my TO-30. I can't get the plunger/piston thingee out of the pressure relief valve bore. It won't fall out if I bang the oil pump on the bench. Any suggestions?
  7. W

    Davis Loader Monstrosity

    Going back to your comments, I suppose I don't understand what you are telling me. The Davis loader has its own hydraulic reservoir and pump. It doesn't use the tractor hydraulics in any way. So do I plug the lines? If so, does anyone know what size plug?
  8. W

    TO30 shifter inspection cover gasket ???

    Thanks Richard. I already made the gasket for the shifter-plate-cover thingee. I was going to use the center for the dipstick-sideplate-thingee gasket.
  9. W

    Oil Pump gasket ???

    OK, Don, thanks. Now how thick is a hot oil thickness? Paper-thick perhaps? No flack on Jeff or John. After reading 200+ messages in the archives, I pretty much get who knows what they're talking about.
  10. W

    Oil Pump gasket ???

    Sorry guys...but I'm talking about the oil pump in the engine - not the pump in the transmission.
  11. W

    TO30 shifter inspection cover gasket ???

    I live in Geauga County, NW of Youngstown...
  12. W

    TO30 shifter inspection cover gasket ???

    Make it myself? I LIKE THAT IDEA! Thank's, Jim. -Wolf (from the opposite corner of Ohio)
  13. W

    How do you clean all the sludge out of hydraulics ???

    I used Jim-OH's method of flushing out the crud with diesel fuel and a garden sprayer. I had water-contamination problems. Jim's method worked very well. A few places the crud seemed to be more stubborn, so I just sprayed that spot for a few seconds more. Tonight I will hose it down again...
  14. W

    Oil Pump gasket ???

    Oil pressure was low in my TO-30. So I did the easiest thing first which was to pull out the oil pump for a look-see. I haven't gauged the impeller-to-body clearance yet, but I did notice that there was no gasket between the plate with the six pan-head screws and the pump body. Somebody did...
  15. W

    TO30 shifter inspection cover gasket ???

    Where can I find a gasket for the cover under where the shift rod sits? I removed the cover to clean out the inside of my transmission. The gasket for the plate is in terrible condition. It fell apart. Now I can"t find a new one. Can someone please help?
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top