Recent content by workhorsewalt

  1. W

    cleaning combine for a seed crop

    Question Just finished my wheat plots for chicken feed. I am growing a small plot of barley (about 3/4 acre) for a seed company and want to get as much of the residual wheat seed out of the combine as possible. I was gonna run the thresher for a bit, blow out with air and repeat with the...
  2. W

    Gleaner E drive belt

    Thanks so much for your help. Got the belt from JV no problem!!
  3. W

    Gleaner E drive belt

    here is the diagram of the belts. It is number 10.
  4. W

    Gleaner E drive belt

    I trashed the drive belt on my gleaner E. Dealer part number 1130239. I have the variable sheave drive. Does anyone know the length and width of this belt. Cant find any info in the service or parts manual. It is belt number 10 in the diagram. Thanks
  5. W

    glener k2 diesel

    What about an f 2 then? They seem bigger. I have an E that is getting wore out and want to get something a little bigger than the E but still small enough for my small farm with narrow gates and roadways. K2 seems like a good option. I do less than 20 acres of grain per yr but a variety of...
  6. W

    gleaner e floods frequently

    didnt see the post till you brought to my attention. That should be the way to go. Thanks!! Gonna rebuild the carb also
  7. W

    gleaner e floods frequently

    Another issue I thought of: It has always flooded easily and maybe I need a carb overhaul. But the mechanical fuel pump went out this spring and I replaced with a Carter electronic one (item #p4070 in line fuel pump) which supposedly has 4-6 psi output. Maybe that pump is overcoming the info...
  8. W

    glener k2 diesel

    Looking for a gleaner k2 diesel with a grain header and possibly a pick up header as well. Good working condition. Located in oregon but willing to travel.
  9. W

    gleaner e floods frequently

    When I go to start my gas gleaner e if floods frequently. Any common causes of this and ways to prevent? Got a good air filter clean fuel. I dont over choke. It sure seems like they are easy to flood though. Thank
  10. W

    gleaner E positive ground?

    Hi Took the battery our of my Gleaner E and neglected to see which side the pos and neg battery terminals are configured. Are all the Gleaner E's positive grounded? Is there anything bad that can happen if I hook up wrong, and if some are positive battery to ground and some are negative ground...
  11. W

    gleaner e fuel pump leak

    Hello. Th gleaner E i have with a gas engine has a leaking fuel pump. It is leaking our an indentation where the screw driver is pointing in the pic. Where can I get a replacement or seal/rebuild kit (possibly NAPA?) or any possibility of replacing with a electric pump?
  12. W

    JD 2240 tractor 3 point hydraulic issue

    Thanks very much TX Jim. I will give these things a try!!
  13. W

    JD 2240 tractor 3 point hydraulic issue

    I posted this a while back but it didnt seem to post, because I cant find the thread. 2240 tractor, 3 point is slow and chattery and sometimes slow or delay in raising, and wont stay in the down position when you are using a brush hog or an implement that is bouncing around and the implement...
  14. W

    JD 7700 combine

    Thanks to all for the great info.
  15. W

    JD 7700 combine

    What is the smallest grain header you can get for this combine? How wide are the pickup headers? I want to use it for wheat and oat grain and for beans if possible on a small scale
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top