(800) 853-2651
SHOP NOW

Recent content by wsm

Yesterday's Tractor Forums
  1. W

    830 horsepower increase

    Thanks for all of the help. Just trying to learn a little. Scott
  2. W

    830 horsepower increase

    What hp can i reach being realistic? Maybe around 90-95? I am just trying to find out what can be reached without turbos and still have a daily usable tractor. Thanks for all of the help. Scott
  3. W

    830 horsepower increase

    I am restoring a 830 John Deere and have the motor bored 125 over and have new aluminum piston. I have larger exhaust valves installed and I am going to have the injectors rebuilt. I wat to get around 100-125 hp . What should I do to get to this point. I am trying not to go to extreme...
  4. W

    John Deere 830 parts needed

    I am working on a 2 cylinder John Deere 830 electric start and i am looking for a couple of parts. I need the floor pan where your feet set and the seat support, the flat panel that goes between the dash and the floor pan,and a float ride seat assembly minus the battery box. I you know where i...
  5. W

    5020 with Kinze Conversion

    Either
  6. W

    5020 with Kinze Conversion

    I am interested in purchasing a 5020 with the Kinze Conversion and was looking for advise and if anyone know where i can find one. Thanks,Scott
  7. W

    John Deere 2 Cylinder Deisel Pullers

    My 16 year old son is looking for a tractor to restore for FFA and he is wanting to do a 2 cylinder deisel. He also likes to pull at the tractor pulls and i was wondering what everyone thought was the best 2 cylinder to pull with and why. I am looking for an electric start. We are trying to stay...
  8. W

    FFA Project Problems with B Clutch

    We stopped as soon as we saw this happening but thanks for the advice.
  9. W

    1936 John Deere B FFA Project Need Help

    Thanks, great bunch of information.
  10. W

    1936 John Deere B FFA Project Need Help

    I have found out that the timing is off on a tractor that my som and i are rebuilding for FFA. When we reinstalled the cam we didnt line up the timing marks. Is there any way to get these in line without removing the cam again? Can we do anything with the crank? By raising up the govener can we...
  11. W

    1936 b John Deere FFA project starting problems

    The tractor is out of time. When i put the crank back in i did not line up the timing marks. (rookie) I am now trying to figure out how to get the gear to line up. We raised the govener and the cover over the end of the cam and we are about an 1/8" from being able to trun the cam to line up the...
  12. W

    FFA Project Problems with B Clutch

    We are still working on the b and time is running short. We tried to pull start it last night and when it is in gear the clutch does not take it out of turning the motor over. You can take it out of gear and it rolls ok but when you put it in gear it turns the motor over. It seems like the...
  13. W

    1936 b John Deere FFA project starting problems

    I am working on a 1936 John Deere b. I have rebuilt the motor,carb and had the mag rebuilt. I was trying to get it started and have not had any luck so far with trying by hand. It doesn't seem that i am getting much fuel up to the motor. We have gas at the carb. Any advice? We are trying to get...
  14. W

    Leaking stud bolts and pto seal

    Thanks for the help Kurt.
  15. W

    Leaking stud bolts and pto seal

    Do you know the part number by chance? I am going to call the dealer and that would make it alot easier.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top