(800) 853-2651
SHOP NOW

Recent content by yeah thats it

Yesterday's Tractor Forums
  1. D

    pistons, rings and sleeves

    the serial number book that i got from this website shows that my 8n is a 1951. but i was looking at the repair manual and in the front of it it has all the serial numbers for the years of the 8nand it shows that it is a 1950, anybody else see that?
  2. P

    oliver hart parr wide front tractor

    check this on ebay http://cgi.ebay.com/oliver-hart-parr-70-farm-tractor-FACTORY-WIDE-FRONT-WOW-/270692560321?pt=LH_DefaultDomain_0&hash=item3f0688adc1
  3. B

    MF Fluids

    I am going to change the fluids in my 1956 MF50, spec book says "API Service Class "MS" Oil" for crankcase and straight mineral oil SAE80 or 90 for hydraulics/tranny/diff. What does everybody run in their old tractors for oil? I bought the tractor a couple years ago and haven't put many hours on...
  4. K

    steering parts

    how do you know if you have a 9n or 8n
  5. L

    carburetor

    My John Deere D will only run when the choke is on half way .It will quit when the choke is open all the way. It is a Marvel,and has just been rebuilt. It has two adjustments, idle needle,and load needle.I have tried every position,and no luck. Les
  6. D

    LeRoi engine

    I just acquired an old LeRoi engine. I'm unable to find a model number on it - much less a date. However, it has a large "S" cast into the head on the front and some sort of numbers" "2 28" on the rear of the head. Can anyone help me identify it? I'd like to restore it but need the info...
  7. A

    Is the 504 a good tractor?

    I know where there is a diesel 504, don't know much else other than it's at a non-IH dealership. I use an 8N Ford now for pushing snow and fetching wagons, but would like a slightly larger, newer tractor for this work and running a pto augar. What are the owners of these tractors saying? Should...
  8. I

    1085 w/perkins

    I have a chance to overhaul the engine on this model and I am not familiar with the Massey line and the perkins engines. Is there anythhing special that I need to know? I have been told that there can be 2 different engines used? Was told that a dealer wants 10K to do this job,how far off is...
  9. B

    M starting problem

    Howdy, My '50 M has been sitting for about a year, tried to start it and it fired up and died , won't restart. I have read posts on here that M's don't like to be choked. My question is----why is it when I choke it the gas drips on the ground, but the plugs don't get wet? I could leave the choke...
  10. F

    price

    Have chance to buy first JD, own farmall&oliver.It"s a "40" JD B org. good shape,runs good comes with new frt.&rear rims,tires weather ck. also has a(#5JD sicle bar)can some give me an idea what the going price might be. Love these old tractors! Thanks Bill
  11. C

    H engine question.

    Hey guys, I am finishing an engine for my H. My question is there is a threaded hole in one of the oil galley ports that is cast into the inside of the block. There is no plug in it now. I thought there was before the block went to the machine shop. Do any of you guys know what I'm talking...
  12. C

    Cub Cadet AGS transaxle oil?

    Can anyone tell me what oil they use in the Cub Cadet AGS transaxle? This AGS (Auto Gear System) is the one with the pedals for forward and reverse, but isn’t a hydro. I have a 2160 model with 350 hours, the transaxle oil level is just above the MIN, and I’d like to top it up. Local CC dealer...
  13. E

    Stanadyne (Roosa Master) Injection Pump

    I have a Stanadyne Injection pump for sale in the photo ads if anyone is interested.
  14. I

    JD 60 - 1st gear

    I just purchased a 52 model, based on serial number, JD 60. Not sure if I got the low first gear or not. One person told me that if it had square axle housing if was the slow gear. Another person told me that since 1st gear was directly across from Reverse, I had the fast first gear. Don"t know...
  15. J

    Delta Homecraft Press

    I just spoke to someone about this Delta Homecraft 11" table top drill press for sale.He said the motor mount's on the bench and that the press swivel's I guess for storage.He said it's old but has no picture's.The height of about 3 feet sound's good because I want to put it on my bench in my...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top