(800) 853-2651
SHOP NOW

Recent content by Zach0485

Yesterday's Tractor Forums
  1. Z

    White 4-210

    Broke the 6 bolts that connecect the over/under to the drive shaft fange. Is there a simpler way other than removing the o/u to get the broken bolts out?
  2. Z

    White 4-210 transmission output flange bolts

    Ok thanks!
  3. Z

    White 4-210 transmission output flange bolts

    Broke the 6 bolts the the connecect the over/under to the drive shaft fange. Is there a simpler way other than removing the o/u to get the broken bolts out?
  4. Z

    D10 series 3 clutch

    I will have to measure tomorrow..but it was probably 2 to 3 inches just guessing. Far as I could tell the splines was in good shape. The old bushing that came out was worn badly and very uneven
  5. Z

    D10 series 3 clutch

    No I didn't try it on the bushing on the shaft. It didn't really pull that hard when pulling it together with the bolts
  6. Z

    D10 series 3 clutch

    The bushing is also new
  7. Z

    D10 series 3 clutch

    Did not check the clearance. Got it together and pulled it together the last 1/2 or so with the bolts
  8. Z

    D10 series 3 clutch

    Yea, I shut it off and put in gear then started it just now. It wants to move regardless of the clutch pedal being pushed in. I can push the clutch and breaks and it will hold it stop it and not kill it. I've adjusted the linkage and makes no difference
  9. Z

    D10 series 3 clutch

    Well nvm on the picture won't load
  10. Z

    D10 series 3 clutch

    Replaced the clutch, now it won't go into gear, just grinds. Wondering if I got the clutch plate in backwards. I put the part that sticks out towards the rear of the tractor like in the pictures. Any help would be greatly appreciated
  11. Z

    White 2-180

    Yea, the linkage going back to the console
  12. Z

    White 2-180

    I tore the console apart...and unhooked the linkage from the shifter. I took it out of park and tried moving the linkage that shifts the gears and I can't budge them. I thought I had it working at first as I got it to shift at first. Now nothing. Has to be something simple as I drive it into the...
  13. Z

    White 2-180

    I was afraid of that....
  14. Z

    White 2-180

    New to me white 2-180 series 3, having issues getting into gear, was stuck between the high and low deck, I somehow got it to move between the upper and lower, but it will not go into any gear especially reverse. The shift linkage is a sloppy, It don't appear anything is out of sync. Any help...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top