(800) 853-2651
SHOP NOW

Recent content by ZacharyDavis88

Yesterday's Tractor Forums
  1. Z

    To20 3point lift

    I have a manual is why I was asking cause it says it should without it . says it should work automatically
  2. Z

    To20 3point lift

    So it will only operate up and down with the PTO engaged correct? How do I protect stuff from getting into the shaft that spinning in the back if I run a plow
  3. Z

    To20 3point lift

    My 3point lift will not wrk unless i have the pto engaged. Why is that? Isn't it suppose to work without the pto engaged?
  4. Z

    To20 rebuild

    The book is saying to coat the head gasket with commercial sealing compound or cup grease anybody know what their talking about? Can i use rtv gasket sealant?[/i]
  5. Z

    To20 fresh rebuild z129

    What motor oil would y'all recommend a certain type
  6. Z

    To20 fiber thrust washer

    It also talks about one being for the camshaft to?
  7. Z

    To20 fiber thrust washer

    It won't let me go to the site
  8. Z

    To20 fiber thrust washer

    Trying to find out what a fiber trust washer is. This came in the kit. Is this what it is?
  9. Z

    To20 drain hole in block

    There is a freeze plug in this hole when I pull it out will there be threads in it or will I have to rethread it
  10. Z

    Massey ferguson to20

    [size=18:ba674b091b][/size:ba674b091b] Thanks everyone for the help
  11. Z

    To20 fiber thrust washer

    I'm not sure what there meaning by this but its what came in the kit i bought I need help identifying the fiber thrust washer this is how i have it. Wrong? Right? It says same thrust washer for camshaft end play I have the brass looking washer on crankshaft side of front main bearings and one on...
  12. Z

    To20 rebuild

    Thanks for the help i appreciate it
  13. Z

    To20

    ok thank you very much that what I needed to know
  14. Z

    To20 rebuild

    I have a few questions will add pictures to help explain need to know if there's anything else or what I need to do to the rear main bearing packing material after I fill the holes and cut the excess off. Also is there a purpose for the hole that is on the back of the old screen that's in the...
  15. Z

    To20

    I was curious if a z120 head is the same as a z 129 head. I am rebuilding a z120 and was curious if a z 129 would be compatible and work on the z120 Block
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top