Clutch stuck jd 420

lefties

New User
Was using it a little without trouble then 1 day i pulled a gate with it and shut it off. When i restarted it ,it woukdnt go in gear only grind...ive tried running it in several gears by lowering idle as low as it will go and depressing clutch and quickly popping it into first....nothing helps.
 
Was using it a little without trouble then 1 day i pulled a gate with it and shut it off. When i restarted it ,it woukdnt go in gear only grind...ive tried running it in several gears by lowering idle as low as it will go and depressing clutch and quickly popping it into first....nothing helps.

First check the clutch adjustment by the book. However, it sounds like you may have to split the tractor to access the clutch and find the problem.
 
If you’ve got a reverser, make sure it’s in the forward (or reverse) position. When I first started my 420 it would t move F-R. I discovered the reverser wasn’t fully engaged. Bingo, it works fine.

Does you clutch have a strong peddle? You should feel an inch or so of just spring pressure free play before it starts disengaging with a firm foot.

I put a completely new clutch in, surfaced flywheel with new ring gear, disc, pressure plate and throw out bearing. It’s too grabby, I need to slip it some to break it in.
 
These is the best manuals I have, it’s a reprint of the original JD parts manual. I also use service manuals, Jen Sales reprint and a Clymers (I think).

The Big Book part numbers are true to what a dealer uses to make it easier and more professional to order JD parts.
 

Attachments

  • IMG_9373.jpeg
    IMG_9373.jpeg
    1.9 MB · Views: 0
  • IMG_9372.jpeg
    IMG_9372.jpeg
    1.6 MB · Views: 0
  • IMG_9371.jpeg
    IMG_9371.jpeg
    1.7 MB · Views: 0
The 420 and 430 service manual is John Deere publication number SM2019. It recommends having SM2013 (for the 40 series) as well since SM2019 refers to using info in SM2013, they figured the dealers already had SM2013 so why bother to include it in SM2019, just point the mechanics to where to find it. They also reference SM2000 (Tractors & Engines, Overview of older tractors, all models prior to and including the 435) which they expected the dealers to already have.
 
Yes guys,i did use the adjustment cam...didnt change anything at all. I do have a strong pedal it just isnt doing anything ..ive adjusted and readjusted. As i said in my previous post i bought it from a jd mechanic and it ran perfect...i only use it a little as i have many other tractors but had run it 5 minutes earlier with no probs,then shut it off. When i restarted it it wouldnt go into gear just grinds. The jd mechanic had no pedal freeplay in it so im hoping its not finished. I dont know what a reverser is please enlighten me. It is the optional 5 speed.
 
Yes guys,i did use the adjustment cam...didnt change anything at all. I do have a strong pedal it just isnt doing anything ..ive adjusted and readjusted. As i said in my previous post i bought it from a jd mechanic and it ran perfect...i only use it a little as i have many other tractors but had run it 5 minutes earlier with no probs,then shut it off. When i restarted it it wouldnt go into gear just grinds. The jd mechanic had no pedal freeplay in it so im hoping its not finished. I dont know what a reverser is please enlighten me. It is the optional 5 speed.
I don't think it has a reverser if it's a ag tractor and not a Industrial one.
 
I don't think it has a reverser if it's a ag tractor and not a Industrial one.
If it had a reverser, it would have a lever to shift it on either the right or left side of the dash cowl and which type of reverser it had. As J. Wondergem posted they were not as common on Ag tractors as the industrial models.
 
Sounds like the pilot bearing in the clutch locked up and won't let the clutch stop spinning. #23 in the picture.
 

Attachments

  • Screenshot 2026-09-29 at 10.48.15 AM.png
    Screenshot 2026-09-29 at 10.48.15 AM.png
    71.8 KB · Views: 0
Sounds like the pilot bearing in the clutch locked up and won't let the clutch stop spinning. #23 in the picture.
Pilot bearing is in the flywheel, not inside the clutch. If it locked up and seized to the transmission input shaft, it would keep the transmission turning even with the clutch disc disengaged from the flywheel and pressure plate. There would be no change in how the clutch pedal works or feels if that is what happened.

In any case this appears to be a split the tractor to find out what is wrong.
 
If it had a reverser, it would have a lever to shift it on either the right or left side of the dash cowl and which type of reverser it had. As J. Wondergem posted they were not as common on Ag tractors as the industrial models.

I guess that puts my 430W in a minority then. It's got the reverser. Fun to drive.
 
Tried these ideas..news guys...decided to fool with my 420 today and readjusted on the clutch cam lobe....didnt stay there but when i was shuffling it around jockying into small door in barn and got rear wheel up against post and hit clutch pedal it would disengage the trans but when tracter isnt in a bind in reverse like that it still does nothing......any ideas? Seems like adjustment setting of some sort...anymore ideas short of splitting? It works at times under load as i explained...i dont buy it needs split.
 
Tried these ideas..news guys...decided to fool with my 420 today and readjusted on the clutch cam lobe....didnt stay there but when i was shuffling it around jockying into small door in barn and got rear wheel up against post and hit clutch pedal it would disengage the trans but when tracter isnt in a bind in reverse like that it still does nothing......any ideas? Seems like adjustment setting of some sort...anymore ideas short of splitting? It works at times under load as i explained...i dont buy it needs split.
If the linkages and bushings on the outside, you can see, are reasonably tight, not a lot of slop, everything else is inside the clutch housing. If the adjustment lock nut isn't holding, try a new nut. Beyond these few items you can access externally, the rest of the parts are inside the housing.

If the friction has piled up or something has gone wrong with a release finger the clutch might slip when you come up against something that resists moving, like the door post. I have to believe if it was just the disc stuck to the flywheel or pressure plate, it freed from being stuck when the tractor stopped when you hit the clutch when it came against the post and would have stayed free when you backed up and after. Can you push the clutch, hold the brakes, and make it slip when it is gear?

I hope most of us are wrong and someone here gives you the magic bullet to save splitting it, but right now my money is on it is going to require a split to fix it right. Good luck.
 
It’s not uncommon for a clutch to stick, but they usually either have to sit a long time or have excessive moisture in the bellhousing. If it was working fine one day and stuck the next, I’d say you have bigger problems. Looks like time for a split.
 
If the linkages and bushings on the outside, you can see, are reasonably tight, not a lot of slop, everything else is inside the clutch housing. If the adjustment lock nut isn't holding, try a new nut. Beyond these few items you can access externally, the rest of the parts are inside the housing.

If the friction has piled up or something has gone wrong with a release finger the clutch might slip when you come up against something that resists moving, like the door post. I have to believe if it was just the disc stuck to the flywheel or pressure plate, it freed from being stuck when the tractor stopped when you hit the clutch when it came against the post and would have stayed free when you backed up and after. Can you push the clutch, hold the brakes, and make it slip when it is gear?

I hope most of us are wrong and someone here gives you the magic bullet to save splitting it, but right now my money is on it is going to require a split to fix it right. Good luck.
No....pushing the clutch isnt doing a thing until its against something. Although it did once in forward after it working in reverse
 
No....pushing the clutch isnt doing a thing until its against something. Although it did once in forward after it working in reverse
You can keep asking for the easy fix, but I would be splitting it to find the problem based on all you have described.

You saying the clutch released when it was push when the tire was against the door post is an indication of what I posted before, it is not just a stuck disc, or it should have freed when that happened. It didn't, that tells me you have an internal problem from the info I read.
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top