Ford Funk Starter

Rich.Fl

Member
I have a Ford Funk with a 6 cylinder "Industrial" flathead. When I tried to start it the starter ran but did not turn the motor. It had a funny grinding sound. No previous starter problems. Video attached with sound. Is this characteristic of anything?
 

Attachments

  • Starter_Ford Funk.mov
    1.8 MB
Could be different things. Could be worn teeth on the flywheel ring gear, could be bad or broken teeth on the starter drive, could be a broken washer on one end of the starter drive spring (which is not uncommon), or could even be a broken nose piece which hold the end of the armature (which is not uncommon to happen on a Funk starter). I'm afraid you will just have to take the starter off and take a look.
 
I have a Ford Funk with a 6 cylinder "Industrial" flathead. When I tried to start it the starter ran but did not turn the motor. It had a funny grinding sound. No previous starter problems. Video attached with sound. Is this characteristic of anything?
Sounds like either a broken ring gear tooth or ring gear came off the flywheel. Grab the top side of the generator pulley and pull toward you to spin the engine forward. Move the engine at least an inch the get that group of teeth out of the way. If results are the same you might have a ring gear popped off the flywheel.

If you have it rebuilt will you post what the starter drive is off of? It has been passed to me second hand from a man who met a Funk brother in the 1990's that they used a Miniapolis Moline starter drive. The nose cone was custom piece and the starter was a regular tractor.

EDIT: It is very important that the nose cone bushing is replaced or at least measured. It is possible to bust the nose cone. There was a machine shop advertising a few years ago they made Funk starters. It is a hear reduction type with machined nose piece to match the adapter plate.
 
Last edited:
Well sure enough the nose cone is broken. Unsure if that can be welded. Trying to figure out about buying a new/used starter. Any suggestions?
THANKS to everyone for their help!!
Funk_Starter_3.jpeg
Funk_Starter_1.jpeg
Funk_Engine.JPG
 
Well sure enough the nose cone is broken. Unsure if that can be welded. Trying to figure out about buying a new/used starter. Any suggestions?
THANKS to everyone for their help!!

I would take it to a good welding/machine shop and see if that can be repaired.
 
It can be welded or brazed. Have seen it done before and will work fine. Just need to get it cleaned up real good so it sticks.
 
Thanks Everyone...I dropped it by a local starter shop that has been in this area for years. They work on a lot of tractors and in fact worked on this starter about 12 years ago. I am hoping they might have some old replacement parts on their back shelf. I'll let you know how things go:)
 
Probably going to have to weld it. the N58-2 noses are "unobtanium". Another choice might be a modern gear-reduction mini-starter.
 
While at the starter repair shop, perhaps the motor can be converted to 12 volts to help the longevity of the nose cone.
 
The fellow at the starter shop was familiar with Funk tractors and recognized this starter. He said he thinks the nose cone was actually also a funk part but has had no luck finding one. The armature shaft was also broken. He is going to try to fix things but suggested I look for a replacement.

Any Ideas?
 
While at the starter repair shop, perhaps the motor can be converted to 12 volts to help the longevity of the nose cone.
I do not know much about starters. Not sure about 6v vs. 12v starters. Why would using a 6v starter cause the nose cone to break?
 
The nose piece is a specific Funk part. It can be repaired with brazing or welding. I have seen brazed ones and it works.

As for the armature, the literature I've seen says that Funk did an exchange program on the armature. You would give them your 8N/9N/2N armature and they would give you a modified armature. I think what they did was add a keyway to the shaft for the different starter drive. So if you get a stock tractor armature or starter, the armature should be able to be modified by a machine shop to match what you have.

For the rest of the starter, the drive was not stock Ford but from some other application, and the rest of the starter was from the stock 8N/9N/2N.
 
The nose piece is a specific Funk part. It can be repaired with brazing or welding. I have seen brazed ones and it works.

As for the armature, the literature I've seen says that Funk did an exchange program on the armature. You would give them your 8N/9N/2N armature and they would give you a modified armature. I think what they did was add a keyway to the shaft for the different starter drive. So if you get a stock tractor armature or starter, the armature should be able to be modified by a machine shop to match what you have.

For the rest of the starter, the drive was not stock Ford but from some other application, and the rest of the starter was from the stock 8N/9N/2N.
Great information...Thanks!!
 
Yes, the Funk N52-8 noses are impossible to find now. I looked for one unsuccessfully when I built my V8 tractor.

If you don't care about originality, a mini starter would fix this. They are 12V. They install from the front and like a Funk starter do not require the Bendix to be on the back side.

The V8 starters will bolt up but have 10 teeth while the I-6 need 9 teeth. They do appear to be out there if you look. May be less expensive in the long run than fixing what you have.
 
Yes, the Funk N52-8 noses are impossible to find now. I looked for one unsuccessfully when I built my V8 tractor.

If you don't care about originality, a mini starter would fix this. They are 12V. They install from the front and like a Funk starter do not require the Bendix to be on the back side.

The V8 starters will bolt up but have 10 teeth while the I-6 need 9 teeth. They do appear to be out there if you look. May be less expensive in the long run than fixing what you have.
Can you tell me more about the mini starter? I know very little about starters:)
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top