Case Centennial Plow Shares

Yesterday I was plowing a sorghum field with my 3-14 Case Centennial model 'B' and my 1956 Case '400'. At some point, I must have hit a rock and broke the point off the rear share. I didn’t notice it was missing until I stopped for lunch and saw it was gone. I kept plowing for another three and a half hours, and it still worked just as well as before. Does anyone know if shares are available for this plow with CX14 moldboards?
Thanks a lot.
(The photos show the plow before, all shined up, and during use.)
 

Attachments

  • 862039863_10235562087452957_765715807605873913_n.jpg
    862039863_10235562087452957_765715807605873913_n.jpg
    947.3 KB · Views: 0
  • 862039823_10235562088852992_2236148100214225778_n.jpg
    862039823_10235562088852992_2236148100214225778_n.jpg
    922.8 KB · Views: 0
  • thumbnail.jpg
    thumbnail.jpg
    102.7 KB · Views: 0
Yesterday I was plowing a sorghum field with my 3-14 Case Centennial model 'B' and my 1956 Case '400'. At some point, I must have hit a rock and broke the point off the rear share. I didn’t notice it was missing until I stopped for lunch and saw it was gone. I kept plowing for another three and a half hours, and it still worked just as well as before. Does anyone know if shares are available for this plow with CX14 moldboards?
Thanks a lot.
(The photos show the plow before, all shined up, and during use.)
Yesterday I was plowing a sorghum field with my 3-14 Case Centennial model 'B' and my 1956 Case '400'. At some point, I must have hit a rock and broke the point off the rear share. I didn’t notice it was missing until I stopped for lunch and saw it was gone. I kept plowing for another three and a half hours, and it still worked just as well as before. Does anyone know if shares are available for this plow with CX14 moldboards?
Thanks a lot.
(The photos show the plow before, all shined up, and during use.)
I use the 16" shares on my 14" S and A Series bet yours are the same you just leave one share hole empty,, the extra length does not affect any thing at all
 
Going back more years than I care to remember, I went to the local blacksmith with my grandfather, and he put the shares in a forge and pounded new tips on broken shares for us. Good blacksmiths are hard to find nowadays. Am I the only one who has those memories, I suspect not.
 
Going back more years than I care to remember, I went to the local blacksmith with my grandfather, and he put the shares in a forge and pounded new tips on broken shares for us. Good blacksmiths are hard to find nowadays. Am I the only one who has those memories, I suspect not.
Yes Mel, I remember going to the blacksmith, Freeman Anschutz, in West Jacksonport, WI with my Dad to get new tips on the plow shares. He was the last person in the county that did that service. That's over 65 years ago. He used to go to the tavern next door and get a bucket of beer every morning to sip on through the day. He could fix just about anything. Now his place is an art gallery.
 
Going back more years than I care to remember, I went to the local blacksmith with my grandfather, and he put the shares in a forge and pounded new tips on broken shares for us. Good blacksmiths are hard to find nowadays. Am I the only one who has those memories, I suspect not.
all of my Centennials and have Oliver and IH plows that use the" hammer" lays on them,, I have some of those new yet some where
I wish there were someone who still could do that work!
those you have are Not the hammer out type someone put later bottoms on your plow at some point, maybe even when it was New,, those are throw away lays,, I can get you the part number of some Adams brand (I think) lays I have,, for 16" ones that will bolt right on , I will also try to take time and get pics of both types,, Major diff between the two
 
If you are the fabricating type person or know someone who is, John Gaard has a you tube channel that shows rebuilding blacksmith type shares. I also have a friend who cuts the leading edge off the old shares and uses a strip of a new throw away share welded in place to rebuild old shares, I have not seen this process in person but seems feasible. Using IH coulters on your plow makes a great plow even better! Also a few kinda' poor shots of the throwaway lays and blacksmith shares to compare to.
 

Attachments

  • IMG_7241.jpeg
    IMG_7241.jpeg
    4.6 MB · Views: 0
  • IMG_7242.jpeg
    IMG_7242.jpeg
    5 MB · Views: 0
  • IMG_7243.jpeg
    IMG_7243.jpeg
    4.2 MB · Views: 0
  • IMG_7244.jpeg
    IMG_7244.jpeg
    3 MB · Views: 0
Nice find! I have two NOS shares in my stash, they are a rare item in this day and age.It would be neat if you could get good pictures of all the decals and have some reproduced.
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top