New to me MF 135 - need advice on getting it running

Ok, next issue to sort out is leaking power steering fluid. After mowing I've got power steering fluid leaking down from the "column" area. Can't see much to actually locate the leak and haven't taken anything apart to gain access yet. Power steering works fine and I can keep topping it off, but it will continue making a mess.

Any common issues leading to this leak I should know about?

IMG_8215.JPG


IMG_8216.JPG
 
It could be as simple as a tube or fitting leak. Hard to say what it might be until you clean it up and actually find where the fluid is coming from.
 
Does anyone have an oil filter canister, bolt, spring, and washer they would part with? Someone was very heavy handed with mine at some point and crushed the end of the canister inward. The seal under the bolt head now leaks because it's trying to seal on a large angled surface rather than a flat surface.

The bolt head, and underside gasket surface are all hacked up as well and it's missing the spring and washer.

I need a fresh start. Please PM me if you've got parts. The alternative is to move to a spin on conversion but I'd prefer to keep it period correct.

Thanks.
I may have the canister parts you need, I replaced mine with the twist on type. One of the bolt holes is broken where it bolts to the engine but all of the other parts are there. I can send pictures so you can see if it's what you're looking for.
 
I may have the canister parts you need, I replaced mine with the twist on type. One of the bolt holes is broken where it bolts to the engine but all of the other parts are there. I can send pictures so you can see if it's what you're looking for.
Sorry, somehow I missed this message.

By the sounds of it, you may have a different type of filter than I do. Mine doesn't have a "mount" that's bolted to the block, which I'm assuming yours does? Feel free to send pics. If it's correct for my tractor we'll certainly work something out.

Thanks!
 
I've got a rear 3 point blade and I'd like to use it to remove the ridge down the middle of my gravel driveway. Is there any setting of the hydraulic levers that would emulate a "float" position? I'd like to see if just the weight of the blade would do what I want. Float seems to be the way to do that.

Thanks.
 

Attachments

  • IMG_2981.JPG
    IMG_2981.JPG
    561.4 KB · Views: 0
I've got a rear 3 point blade and I'd like to use it to remove the ridge down the middle of my gravel driveway. Is there any setting of the hydraulic levers that would emulate a "float" position? I'd like to see if just the weight of the blade would do what I want. Float seems to be the way to do that.

Thanks.
Just drop the Position Control lever all the way down. That will be your "Float" position essentially.
It will be the same on most other tractors, no down pressure on the implement except the weight of the implement.
There are only a few tractors that have actual downforce on the 3-point, AKA you can actually force the implement into the ground.
So if you want your blade to dig deeper, you will have to add more weight onto it.

Hope this makes sense, and good luck!
 
why would you want to remove the crown of the road? It creates water runoff, otherwise a flat crushed stone road allows the water to soak into the roadbed.
 
MF 135 parts book
Sorry, somehow I missed this message.

By the sounds of it, you may have a different type of filter than I do. Mine doesn't have a "mount" that's bolted to the block, which I'm assuming yours does? Feel free to send pics. If it's correct for my tractor we'll certainly work something out.

Thanks!
The MF 135 used at least 3 different engines. It is helpful if you tell which engine you have when you are looking for parts in a long thread like this. I had to look back to find which engine you have in your MF 135. Some Random Guy apparently offered you a filer for a MF 135 with a Perkins engine, you have a Z145 Continental which is different. Below is a link to the MF 135 parts book online. The Continental oil filter is on page 44. I also posted a picture of it so you can see the parts and use the key numbers to ID what you need. You can get the actual part numbers from the parts book.

MF 135 parts book

1793186181730.png
 
Just drop the Position Control lever all the way down. That will be your "Float" position essentially.
It will be the same on most other tractors, no down pressure on the implement except the weight of the implement.
There are only a few tractors that have actual downforce on the 3-point, AKA you can actually force the implement into the ground.
So if you want your blade to dig deeper, you will have to add more weight onto it.

Hope this makes sense, and good luck!
Yep that makes sense, thank you. Much appreciated. Seems obvious one I think about the fact that the 3 point can't apply any downward force.
 
MF 135 parts book

The MF 135 used at least 3 different engines. It is helpful if you tell which engine you have when you are looking for parts in a long thread like this. I had to look back to find which engine you have in your MF 135. Some Random Guy apparently offered you a filer for a MF 135 with a Perkins engine, you have a Z145 Continental which is different. Below is a link to the MF 135 parts book online. The Continental oil filter is on page 44. I also posted a picture of it so you can see the parts and use the key numbers to ID what you need. You can get the actual part numbers from the parts book.

MF 135 parts book

View attachment 168158

Thanks for linking to the parts Jim.ME. That catalog is very helpful and I always have trouble finding it.
 
That catalog is very helpful and I always have trouble finding it.
You can also “bookmark” replies inside of the YT forums so you can come back to them. At the upper right of the reply you’ll see a banner icon with a triangle cut out of the bottom. You click that and when it turns red it is added to your YT book marks, there are also options there to label it. To access it you open your profile (lime green circle with a 3 in it) and the book mark list will be right at the top.
Unfortunately in my case I view YT on a phone and it seems when I carelessly scroll I also unintentionally click a lot of book marks. My problem.
 
You can also “bookmark” replies inside of the YT forums so you can come back to them. At the upper right of the reply you’ll see a banner icon with a triangle cut out of the bottom. You click that and when it turns red it is added to your YT book marks, there are also options there to label it. To access it you open your profile (lime green circle with a 3 in it) and the book mark list will be right at the top.
Unfortunately in my case I view YT on a phone and it seems when I carelessly scroll I also unintentionally click a lot of book marks. My problem.
Sweet. Thanks for the tip.
 

Attachments

  • IMG_9325.jpg
    IMG_9325.jpg
    4.7 MB · Views: 0
  • IMG_9326.jpg
    IMG_9326.jpg
    4.7 MB · Views: 0
  • IMG_9327.jpg
    IMG_9327.jpg
    4.3 MB · Views: 0
  • IMG_9328.JPG
    IMG_9328.JPG
    3.5 MB · Views: 0
Sorry I haven't replied, I've been working out of town. But Jim.ME is correct my oil canister came off of a Perkins gas engine. I still have it if you or anyone ever needs one, I only replaced it because the twist on kind was more convenient for me.
 

Attachments

  • IMG_20261106_151944.jpg
    IMG_20261106_151944.jpg
    799.2 KB · Views: 0
Serial data range
It was established in post #13 his is a 1966 by the serial number on the tag. A picture in post # 20 showed the tag on the engine - Continental Z145.

Interesting the info you have doesn't match the info I see on TractorData for a MF 135. For one thing it doesn't show the same serial number range of years.

MF135 a.jpg MF 135 b.jpg MF 135 c.jpg
 
It was established in post #13 his is a 1966 by the serial number on the tag. A picture in post # 20 showed the tag on the engine - Continental Z145.

Interesting the info you have doesn't match the info I see on TractorData for a MF 135. For one thing it doesn't show the same serial number range of years.

View attachment 169028 View attachment 169029 View attachment 169030
It was established in post #13 his is a 1966 by the serial number on the tag. A picture in post # 20 showed the tag on the engine - Continental Z145.

Interesting the info you have doesn't match the info I see on TractorData for a MF 135. For one thing it doesn't show the same serial number range of years.

View attachment 169028 View attachment 169029 View attachment 169030
Wondering that myself
 
Sorry I haven't replied, I've been working out of town. But Jim.ME is correct my oil canister came off of a Perkins gas engine. I still have it if you or anyone ever needs one, I only replaced it because the twist on kind was more convenient for me.
My 1972 MF 125w/ Perkins gas engine has a spin on filter; port side of engine.
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top