Fawteen
Well-known Member
- Location
- Downeast Maine
And they'll stay there.
Now the napa golds are made in Asia!Like anything when you have a low end line to meet a price point the entire brand name can suffer. FRAM has some good stuff but they also have some bad stuff.
I don’t trust wix since Mann bought them.
I’m using mobile 1 extended performance oil and filters on my gas cars with normal change intervals and the best Napa filter on my diesel tractor
I would still put money on most engines fail due to neglect and whatever oil is in the crankcase and filter on the block gets the blame. For every brand oil and filter there are plenty of people out there to curse it and blame it for financial ruin that now has lasted for generations.I’ve never had an engine fail from the oil filter. I think it’s more of a long term thing though. Either the filter doesn’t filter well or causes a restriction and over time your engine gets more wear because of it.
I’ve never had an engine fail from the oil filter. I think it’s more of a long term thing though. Either the filter doesn’t filter well or causes a restriction and over time your engine gets more wear because of it.
Not an engine failure but the last 2 Mobil one filters I used worked loose.I always hand tightened my filters starting in the late 70’s after one time over tightening one.guess I need to use the filter wrench at least sparinglyWith all this discussion of filters. I’m just wondering if anyone has had an engine fail because of a bad filter?
Maybe your grip isn’t what it used to be? Or my main problem is you can’t get a good grip because of the filter location on modern vehicles.Not an engine failure but the last 2 Mobil one filters I used worked loose.I always hand tightened my filters starting in the late 70’s after one time over tightening one.guess I need to use the filter wrench at least sparingly
The installation directions are on most all the filters I buy....gasket contacts + 3/4 turn. I have had a Generac home standby generator since 2014 and the only problem I had with it was the seam where the oil filter canister is connected to the base was leaking because, it was apparent to me when I removed it, that it was put on with a torque wrench set way too tight......at the factory.Not an engine failure but the last 2 Mobil one filters I used worked loose.I always hand tightened my filters starting in the late 70’s after one time over tightening one.guess I need to use the filter wrench at least sparingly
Been changing oil and filters in vehicles and all kinds of machinery for 50 years.these 2 filters are the only ones I have ever had a problem withFor 30 years maybe more I apply grease to the seal and tighten up one full turn. I have performed thousands of oil filter replacements maybe I was before my time. I did have one leak the filter cracked around the base I am sure it was a manufacturing error. Putting motor oil on the seal acts like a lock and worst when you go a full turn that's why I switched to grease. I use to see plenty of other shops oil filter installs its scary to run across so many that felt like they got lucky it did not fall off. I will grantee that anyone that goes behind my installs will say give that man a metal he made sure it would not fall off : ) BTW I use oil filter cap wrenches made for filters I have no problem getting what I install off. Its those that are to cheap to invest in tools to perform the job that mess them up.
Have we been doing it wrong
I have that issue now as well. I’m not old compared to most on this forum but my muscles are getting very weak. I have a hard time opening the drain plug without an extendable ratchet.Not an engine failure but the last 2 Mobil one filters I used worked loose.I always hand tightened my filters starting in the late 70’s after one time over tightening one.guess I need to use the filter wrench at least sparingly
And they'll stay there.
Not sure what you're trying to say there.I get it. It's a little like saying the Coronavirus in back in China, and ready whenever you are.
I figure Mann is better than many. like so many things filters are also getting consolidated. Mann owns Purolator as well. (was Mann/Bosch joint venture) Mann makes alot of OE parts.Like anything when you have a low end line to meet a price point the entire brand name can suffer. FRAM has some good stuff but they also have some bad stuff.
I don’t trust wix since Mann bought them.
I’m using mobile 1 extended performance oil and filters on my gas cars with normal change intervals and the best Napa filter on my diesel tractor
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy