SMTA Diesel

Nebraska Kirk

Well-known Member
I have torn down my SMTA diesel and it’s restoration has begun!

Rear end gears are junk, but I have good used gears out of a 400 to put in there. Engine turned out to not be as bad as I thought. I actually got it unstuck without even trying! I was just loosening the front crankshaft nut when the engine broke loose! Sleeves are still 4” but quite worn so I am going to bore them to 4-1/8” and pop in a god used set of 4-1/8” pistons I have. Crankshaft still looks pretty good, hoping I can reuse rod & main bearings and be good to go. Of course I will be going completely through the fuel system and TA as well. This will make a nice mate for my gas smta.😁
 

Attachments

  • ED761FD5-5965-4B13-88BB-0F3BF44F1163.jpeg
    ED761FD5-5965-4B13-88BB-0F3BF44F1163.jpeg
    135.1 KB · Views: 0
  • 4006C6A2-D794-474C-A0A9-719E2884C38F.jpeg
    4006C6A2-D794-474C-A0A9-719E2884C38F.jpeg
    108.8 KB · Views: 0
  • 92C52CCE-3035-4B13-BBFF-68BF2E79A1C6.jpeg
    92C52CCE-3035-4B13-BBFF-68BF2E79A1C6.jpeg
    140.3 KB · Views: 0
  • 6D2A523B-AF76-46CE-B9E1-792575F5D732.jpeg
    6D2A523B-AF76-46CE-B9E1-792575F5D732.jpeg
    123.4 KB · Views: 0
  • C7691AE8-EEFA-4813-9EA6-2A423C8CEBF4.jpeg
    C7691AE8-EEFA-4813-9EA6-2A423C8CEBF4.jpeg
    137.3 KB · Views: 0
  • 69395146-68D9-461A-AECB-CDCB8929646C.jpeg
    69395146-68D9-461A-AECB-CDCB8929646C.jpeg
    72.8 KB · Views: 0
  • 6D59CC50-7101-4F9D-AF6F-D5BFF8A9CCE7.jpeg
    6D59CC50-7101-4F9D-AF6F-D5BFF8A9CCE7.jpeg
    133.5 KB · Views: 0
  • 56006221-D6EB-4EFD-A9DE-B7D990AE84E0.jpeg
    56006221-D6EB-4EFD-A9DE-B7D990AE84E0.jpeg
    95.1 KB · Views: 0
  • EBD27863-465E-4278-9A33-61F81B214BF5.jpeg
    EBD27863-465E-4278-9A33-61F81B214BF5.jpeg
    90.4 KB · Views: 0
  • 83A7BCEB-D1BC-4CB5-956F-B94E3AC68350.jpeg
    83A7BCEB-D1BC-4CB5-956F-B94E3AC68350.jpeg
    140.3 KB · Views: 0
These gears look a lot better! One gear in the transmission needs to be replaced, but thankfully the one in the rusty transmission is still good. Between the 2 rearends I will have enough good parts for one
 

Attachments

  • 53B05E57-1504-44BE-8420-C8667B15A646.jpeg
    53B05E57-1504-44BE-8420-C8667B15A646.jpeg
    95.1 KB · Views: 0
  • CA08E90F-99AD-4053-A6E9-C7BD61FA10BB.jpeg
    CA08E90F-99AD-4053-A6E9-C7BD61FA10BB.jpeg
    95.2 KB · Views: 0
I plan to.
And magnaflux it also to check for cracks.
You might as well check the head and make sure it is flat too, and make sure the valves and seats are in good condition. Especially check the smaller starting valves and make sure they seal, because if they don't seal you will have lower compression on diesel and lots of other problems.
 
And magnaflux it also to check for cracks.
You might as well check the head and make sure it is flat too, and make sure the valves and seats are in good condition. Especially check the smaller starting valves and make sure they seal, because if they don't seal you will have lower compression on diesel and lots of other problems.
The head is getting a complete valve job and will be resurfaced too. I am able to reuse the intake & exhaust valves and have already ground them. Seats will be ground and all new starting valves have been purchased.
 
I’ve made a little progress. The rearend is cleaned & primed and ready for all the gears to go back in. Have also been working on rear rims,cleaned and primed them. I used Rustoleum restore on the outside to prime and am going to try spraying it with Rustoleum bright cold galvanize
 

Attachments

  • 017F6003-CC55-448D-965C-9D695B38D566.jpeg
    017F6003-CC55-448D-965C-9D695B38D566.jpeg
    2.2 MB · Views: 0
  • 037F001E-7CA9-437A-8A67-B9D7E4958E51.jpeg
    037F001E-7CA9-437A-8A67-B9D7E4958E51.jpeg
    1.9 MB · Views: 0
I’ve made a little progress. The rearend is cleaned & primed and ready for all the gears to go back in. Have also been working on rear rims,cleaned and primed them. I used Rustoleum restore on the outside to prime and am going to try spraying it with Rustoleum bright cold galvanize
You tube's "Just a few acres farm" just posted a TA tear down and inspection you may find helpful. He also restored a MD.
 
Yes, I’m familiar with that YouTube channel and have watched a few of his videos. I rebuilt a Farmall 400 gas about 15 years ago and went through the TA and everything so I am familiar with it all, we will see how much I remember from way back then🤣 I do have a service manual and parts book to reference too.
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top