(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. J

    Brushwhacker Skid Steer Cutter

    Does anybody know anything about a 5 foot skid steer cutter named Brushwhacker? I'm trying to see if it is a good cutter to purchase. It has Brushwhacker.com and a phone number (888-547-7950) on it but neither one works now. It is the color yellow similar to bushwhacker.
  2. J

    Vicon CM2400 Mower

    Hi! My breakaway bar keeps slipping when I am mowing. I've took pressure off the spring and retightened it but it still slips as soon as I pull off. Any ideas or should I replace it? Thank you!
  3. J

    Vicon CM2400 Hay Mower

    I am replacing the bearings in one of the cutter heads on a Vicon CM2400. When I press the hub back on to align the holes for the roll pins I cannot turn the gear by hand. It seems like there is to much pressure on the bearings. If I back off the hub some I can turn it by hand but the holes...
  4. J

    Bushhog 2615 Transfer Gearbox Seal Bearing

    I have an output shaft on my bushhog 2615 transfer gearbox that has a leaking seal and a little up and down play. Does the top cover of the gearbox need to come off to replace the outer bearing and seal or can this be done from the shaft end? Thanks for any help?
  5. J

    Bushho 2615

    I just purchased a older used Bushhog 2615 and wanted to replace the oil in the power divider gearbox. Does anybody know how much oil it holds and the type? I believe on the cutter gearboxes it's 6 quarts of 80w90 but wasn't sure on the power divider gearbox. Thank you!
  6. J

    Massey Ferguson 165

    Hi, I was wanting to install a block heater on a MF 165 with the ad4203 diesel. On the left side of engine there is a plug in the center with a small threaded plug located in the center of it and towards the back of the engine on the left side there is a freeze plug. In the attached photo...
  7. J

    John Deere 4230 PTO Detente Lever Broken

    Hi, I have my PTO Clutch cover off tractor to replace the PTO Detente Lever arm that has broken. I have been tieing up PTO lever with bungee cord for awhile and decided to fix the issue today. While I have the main cover off the tractor I cannot remove the small cover that is bolted onto...
  8. J

    Stanadyne DM4 John Deere 4230

    I have a Stanadyne DM4 injector pump that may be leaking fuel into oil on my John Deere 4230. I've already replaced the lift pump. I was wondering how hard it is to replace seals on this pump? I found a seal kit for $30 but didn't know if this could be something accomplished at home or if it...
  9. J

    1977 John Deere 4230 Fuel in Oil

    I have a 1977 John Deere 4230 that is still getting fuel into oil with a new fuel lift pump installed. The engine always had a little white smoke but I noticed it is smoking a lot more than usual especially at low idle and when the engine idles up. It even sounds like the engine may be missing...
  10. J

    John Deere 4230 Rattle Noise

    I have a John Deere 4230 Quad Range that I noticed a rattle noise on today. The rattle happens when you idle the engine up. It only lasts for about a second or so but sounds like marbles bouncing around. It's hard to tell where it is coming from but it's around the back of engine or around the...
  11. J

    John Deere 4230 PTO Lever Loose

    I have a 1977 JD 4230 that the PTO Lever is loose and I have to hold it in place with a bungee cord to keep from engaging and disengaging. Does anybody know what may be causing this and how to fix it? Thanks for any help!
  12. J

    Bushhog 306 Input Shaft Bearing Play

    Hi, I have a bushhog 306 that the input shaft has play up and down in it. It doesn't have any play pushing and pulling out on it so I am thinking the bearing is worn. This has caused the seal to leak. How easy is it to replace this bearing? Any info is appreciated. Thanks!
  13. J

    MF 165 Diesel Alternator Not Charging

    Hi, I have a MF 165 that I can't get alternator to charge. It has been this way for awhile so I have been jumping it off. I decided to replace the alternator thinking it was bad with a 7127 one wire alternator from Advance Auto and it still isn't charging. I jump the oil pressure switch...
  14. J

    Bush hog 306

    Hi, I have a bushhog 306 that leaks a little oil from the input shaft seal. Does anybody know how you change this seal? Any help would be appreciated. Thanks
  15. J

    MF 165 Clutch

    Hi, I have a MF 165 that keeps shearing the cotter pins that goes in the little dowels on the fingers on the pressure plate. This is the second clutch I had to put in because the first one done the same thing and a piece of the clutch finger broke when this happened. I have tried different...
  16. J

    1953 Farmall Super M Running Poorly

    I have a Farmall Super M that the engine was stuck. I removed the head and freed it up by soaking the pistons and got them to work loose.I put the engine back together, rebuilt the carb and installed new plugs and wires. After cranking and running some, the engine is popping through...
  17. J

    John Deere 4230 Warning Light Flasher

    Hi, My warning lights on my 4 post canopy are not working at all. I can't find where the flasher is located. I looked under cowl but couldn't find it. Does anybody know where it is located and if it would cause the warning lights not to work? Thanks
  18. J

    John Deere 4230 PTO Shifter Won't Stay in Position

    I have a 1977 4230 that the PTO shifter won't stay engaged or disengaged. I have to use a bungee cord to hold it in position. There is some play in the linkage but not sure if that is the problem. If I don't use the bungee cord to hold the shifter it will vibrate out of position. Any ideas on...
  19. J

    John Deere 4230 Hydraulics

    I have a JD 4230 that I purchased not long ago. When I bought it I changed all the fluids and filters and cleaned the hydraulic screen filter. I noticed after bushhogging for about five hours the scv and around the rear end seemed hot. I check the temperature with my temp gun and it was...
  20. J

    John Deere 4230 Lights Wiring Diagram

    I have a 1977 John Deere 4230 with four post canopy that I need a wiring diagram for the lights. I bought the tractor used and the lights never worked on it. Now Im trying to see if I can wire them back up. Some of the wires and connectors are broken and some wiring may be missing. Does anybody...
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top