(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. A

    TW25 temperature senders

    Hi guys, my Ford tw25 series 2 has 2 temperature sensors. From what I understand the top one is an on/off to run the idiot light, the bottom is variable resistance to run the bar graph on the digital dash. Does anyone know the part numbers for the 2 senders or where to look. The picture on the...
  2. A

    1085 Multipower

    Hey guys, I asked on the Massey page and didn't get a response so I thought I'd try here. I need to replace the plates and disks in my multipower unit on my 1085. Is there a quality difference between Massey Ferguson (Sparex) parts and hy-capacity? Pricing seems about the same. Any other...
  3. A

    1085 Multipower

    Hey all, I need to replace the plates and disks in my multipower unit on my 1085. Is there a quality difference between Massey Ferguson (Sparex) parts and hy-capacity? Any other recommendations? Thanks, Alf
  4. A

    John Deere 510 (Lanz)

    Anyone happen to know how you change/check hydraulic oil on a John Deere 510 (Lanz) farm tractor. I don't have an owners manual. Shop manual says gear box and final drive hold 31 liters,rear axle housing holds 0.8 liters,and the hydraulic system holds 10 liters. I pulled the plugs on the bottom...
  5. A

    1085 powershift

    Hey Guys, low pressure hydraulics question 1085 with cab. If I put a gauge on the pto port at idle and turn the pto on and off, pressure is 250 psi one way and 0 the other. If I move the gauge to the powershift port (right hand side of the firewall) at idle I get 225 psi in low and 125 psi in...
  6. A

    3 pt hitch hydraulics

    Hi All, I am trying to set up my 3 point hitch hydraulics on my Massey 1085. The I&T manual notes I will need tools NFN 1080B, NFN 1080C, and NFN 1080D. Does anyone know if these tools are available anywhere, or if there is a way to set up without them? Thanks.
  7. A

    457 silage special mega wide

    Hi Guys. I was wondering if you could help me. My boss has a 457 silage special round baler with a mega wide pickup purchased in about 2007. He had some broken pickup teeth and asked me to replace them. I ordered the teeth and the local dealer got me part number FH304576. When I went to install...
  8. A

    Ford 3000 question

    Hi all, I decided to move my front wheels out on my 69 Ford 3000 to try to keep from driving on the windrow when raking hay. Problem I am having is, as the wheels go out, they also move back which causes toe out. I have moved them about half way out but the adjustment on both wheels drag links...
  9. A

    I need a Massey expert

    Hi Guys, The 3 point hitch lift cylinder on my 1085 Massey was getting pretty weak, especially when the oil warmed up. Also when the tractor was shut off it would drop down to the ground in about a minute. So I pulled it apart and found the piston, cylinder and rings were all pretty badly...
  10. A

    2950 fwd solenoid

    Hi all, I am working on a 2950 that has been used in the bush or something and wires are pulled off/ missing on the fwd solenoid. Does anyone have a website, wiring diagram, or know what is supposed to connect to the three solenoid terminals. The electrical plug is totally missing from the...
  11. A

    Idle speed on a 7950 Kabota

    Anyone know what idle speed is supposed to be on a 7950 Kabota. Customer is complaining about an oil pressure light coming on but I am pretty sure it is supposed to idle faster than 600 rpm. I looked in the owners manual and couldn't find it. Thanks Alf Roberts
  12. A

    Fuel Tank Repair

    Will fiberglass work to patch a rust hole in a diesel fuel tank, or will the diesel fuel eat it and leak? Any other better repair ideas? Kabota M7950DT sticks a reserve fuel tank behind the grill, but in front of the rad, and then puts the battery above it. In time battery acid leaks down and...
  13. A

    International 8330 Mower conditioner

    Working on a neighbours 8330 mower conditioner and the bearing in the idler sprocket on the main drive chain went. So I replaced the idler and tried to tighten the chain, but it pulled really tight on the top and stayed slack on the bottom. I am thinking this has to do with the timing of the...
  14. A

    135 Massey

    I have a neighbour with a 135 Massey with a loader. Between your legs, on the top of the rear axle hydraulic cover, there is a valve with a 2"lever that rotates about 90 degrees up and down, one way operates the 3 point, the other way runs the loader. If I take the handle off and remove a snap...
  15. A

    JD combines

    In the early 70"s John Deere had the 3300, 4400, 6600, and 7700 series combines. Later on these upgraded to the 20 series, the 3300 was dropped and the 8820 was added. My question is, could someone explain the next series of upgrades......that is what did the 4420, 6620, 7720, and 8820 each...
  16. A

    Ford 3000 Generator

    Hi guys, I have a Ford 3000 with a charging system that isn"t working. When it is working the original generator only put out 22 amps, not really enough to run a good set of working lights. The simple solution to my problem is to use a GM alternator, but if I do that I loose my Tach drive. Is...
  17. A

    6600 Straw walker horn

    Several years ago I bought a 6600 Deere and it has worked very well, but 3 times over the time I have owned it I have plugged canola over the chopper and the slip clutch on the walkers hasn"t let go until the end section on the walkers has bent. According to the manual, there is supposed to be a...
  18. A

    Allis Chambers 2000 plow

    I bought an Allis Chambers 2000 4 furrow plow years ago 2nd hand with no manual. Does anyone know how much hydraulic pressure should be applied to the hydraulic reset accumulator? Thanks, Alf Roberts
  19. A

    John Deere 5020

    I recently picked up a John Deere 5020 that has a few rear end problems. I know I will need a new left trumpet with ring gear, and the planet gears, and will probably find a few more surprises inside but I got it for a reasonable price so I am happy. A few questions: 1.) Does anyone have a spare...
  20. A

    6600 Transmission

    My 6600 has been popping out of third since soon after I got it used 6 years ago but by the end of last year I had neither third nor fourth. I have pulled the transmission (manual 4 speed) and found one bearing pitted badly but still working, and the gears themselves look good. The problem...
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top