(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. R

    40b won't move

    Happy New year everybody, I have a my 40B its a manual shuttle ,while driving it the other day the tractor just stopped moving I was in high gear at the time it would move a couple more times but only for a few feet.I tried every gear but no movement. The first thing I thought of was the...
  2. R

    54 naa

    Need some help on my NAA I need to replace the lift ram arm (broken) I can get the lift arm shaft to go only so far. In the parts book it looks like the shaft is bigger in the center so then it would be bigger then the bushings? So how does it come out? Thanks
  3. R

    NAA no lift power

    HI, Need some help with my NAA three point will lift but won?t hold a load ,I want to check they pump pressure to start but don?t know where the access point is.Tanks
  4. R

    2n hyd pick up tube

    need some help with my 2n noticed recently my three point would go up but wouldn't hold weight. I found the pick up tube from the pump to the rockshaft piston has a split in it. I can't find any available parts ,could fix it but would rather replace it if possible.
  5. R

    235 block core plug

    need some help on a 235 diesel, I'm replacing a head gasket and noticed some coolant passages in the block have core plugs in them with holes i'm guessing t slow down coolant flow, these plugs are corroded and should be replaced but I can't find them in the parts breakdown. has anyone seen this...
  6. R

    580b brake seal leak

    need some help with my 580 I'm resealing a rt side seal leak that saturated the brake linings. I found some posts on how to replace the larger seal but I need to replace the smaller seals (2) around the differential lock shaft. can I remove the whole assembly? doing it in the vehicle seems very...
  7. R

    farmall A fuel leak

    HI,I have a Farmall A that I can't get the carb to stop leaking when it's not in use. I have to shut off the needle valve in the sediment bowl or fuel will continuously drip from the carb throttle and bowl to cover gasket. I have went through the carb replaced needle and seat, changed the float...
  8. R

    1715 ford

    HI, I have a ford 1715 with a j843 engine I just rebuilt it. 1. engine was bored over.040 block was decked. 2. valve job, head was resurfaced 3.new pistons, rods bushings replaced and fitted. 4. rod and main bearings replaced. after starting engine after careful break in 60 psi oil pressure,190...
  9. R

    mf 35 braking

    HELLO ALL, I have a mf 35 I recently bought, I felt it had poor braking ability (could not lock up wheels). so I removed the wheels for an inspection I found the axle seals to be leaking and shoes had oil on them. so I removed the axles ,replaced the seals inner and outer , put new shoes and...
  10. R

    ford 1715 engine

    need some help on this engine I'm rebuilding it because of some compression issues, I'm putting the timing gears back on and setting the timing. they say in the manual to line up the marks on the crank,idler and cam gears when I do that number 3 or the most rear cyl is on top dead center...
  11. R

    ford 1715 engine specs

    HELLO ALL, Its been some time since I've been here but here goes. I have a ford 1715 with a shibaura j843 engine it will not start. compression readings were #1-300 psi,#2-190psi and #3-200psi. leak down test showed #1-75%,#2-78%,#3-85%. I decided to tear it down found poor sealing on valve to...
  12. R

    Rail trolly

    I'm trying to improve the way I split a tractor and have recently seen a system in a Massey Ferguson repair manual. They called it a rail trolly it looked like it consisted of some bearings mounted to a plate that road on a set of rails. Does any one have any knowledge of this and what it takes...
  13. R

    mf 30e

    Hello, I have a mf 30E with instant reverse trans I have a hyd leak from inside the bell housing area it doesn't look like the trans pump is leaking, could the torque converter be leaking on this model? thanks.
  14. R

    Superior equipment loader

    I have a front end loader manufactured by superior equipment I'm in need of some seal kits for the lift cylinders Does anybody know where I could locate them. Thanks
  15. R

    2n weak spark

    I know this subject has been bet to death but here goes. I'm working on a friends 2n he said it started running poorly and has put a lot of parts in it cap,rotor,points,coil,wires. It has very weak spark 1/8 or less . I've had the distributor out and went through all the Cks (Bruce va) had...
  16. R

    504 pto

    Hello all,I have a int 504 that the pto stopped working,I took the housing off the tractor and found the retainer pin for the shaft to shift fork broke. Nothing was damaged but I can't figure out how to get the assembly apart to repair the fork. Any help would be appreciated .
  17. R

    504 pto

    Hello all,I have a int 504 that the pto stopped working,I took the housing off the tractor and found the retainer pin for the shaft to shift fork broke. Nothing was damaged but I can't figure out how to get the assembly apart to repair the fork. Any help would be appreciated .
  18. R

    Timing gears on 1220

    Need some help with a 1220 ford . I have poor compression on #1 and 3 cyls number two will make smoke but the other two won't. I pulled the head and had it gone over at the machine shop put it together with same results. I switched injectors with same results,the pistons seem tight in there...
  19. R

    445a

    Hello,I just bought a 445a ford industrial I knew it had a missing cyl when I bought it. When I took the head off I found #3 cyl piston badly pitted and the cyl worn . I have to take the engine out does any one know how long it should take. Thanks
  20. R

    Super 55

    I have a super 55 my pto wasn't working correctly so I split it and rebuilt the pto clutch. I see that the adjustment of the clutch pact is 32 lbs pull on the lever. My question is what holds the clutch lever engaged once you pull it up to engage it. Thanks
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top