(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. J

    Gear grinding new clutch

    Hi guys. I just completed a clutch replacement on a Farmall Super A. Replaced clutch, pilot bushing, throw out bearing and new bearing carrier (replaced original graphite bearing). Initially the clutch rod and yoke were making contact with clutch finger adjust screws when fully depressing...
  2. J

    Tool to press on crankshaft pulley for Super A

    I am getting close to reassembling the front end of my Super A and need to press the crankshaft pulley back on. For removal I fabricated up a plate to go behind pulley and pulled off with a hydraulic jack. I have read several posts about pressing back on. In one post gene bender described a...
  3. J

    Wire on governor cover A and super A

    I'm replacing front seal and cleaning up and painting front end of my Super A. I have the governor cover off and am getting ready to degrease and paint it. On the governor cover for my Super A and also on my A, there is a thin braided wire that runs through a hole in the head of one of the...
  4. J

    Procedure to oil Super A fan hub

    I am rebuilding my Super A fan assembly and just want to confirm the proper procedure to oil the assembly. From what I have seen in a couple posts you fill up with the fill screw at top position. Is this correct and do you just fill till oil flows out? Then I saw that you rotate until the fill...
  5. J

    Farmall A - Is this Steering Arm bent?

    Hi Guys, I'm restoring a Farmall A. Now that I've got the steering assembly apart I'm looking at the Steering Arm and I can't tell if it is bent (see pic - section where the Tie Rods connect). Is it supposed to be this way due to the tractor offset. Can anyone with an A or familiarity with...
  6. J

    Question on A steering knuckle

    On each of my A steering knuckles there is an opening on the back side opposite where the spindle comes out. It almost looks like a grease fitting should be there but the hole is not threaded. Can anyone advise about this? Thanks.
  7. J

    Farmall A front axle removal

    Well, I hope this ain't the dumbest question ever asked... I'm pulling the front axle on a farmall a. There is an offset pivot shaft with a pin where the steering unit/gear box mounts. I can see anything that secures the pin in place, no nuts, etc. The end is very banged up like it has been...
  8. J

    Farmall a torque tube removal

    I am getting ready to pull the torque tube from my a. I have the engine block removed. After I get the clutch linkages and pedals etc. removed, will the tube just disconnect after removing the bolt teaching to the transmission? Is there any special removal process I need to consider? Also,a...
  9. J

    Farmall A block DG versus DH cast

    I have a 1946 farmall a with block cast 6342-DH. After removing the cylinder head during restoration I've discovered that the block has a large internal crack so I am looking to replace the block. I have seen one listed with casting 6342-DG. Does anyone know if these blocks are interchangable...
  10. J

    Farmall A steering shaft removal process

    I removed the cover at the front of the gear box and then the cotter pin and nut from the end of the shaft. What now? I thought I'd just be able to twist out from there, but I think there is possibly another step in the process? Let me know, thanks jim
  11. J

    Transmission bell housing case interchangeability

    I have a 1946 farmall a with a cracked bell house case. The cast # is 8638-DC. I have opportunity on a parts tractor but the case is cast #8638-DE. Does anyone know what is different between these two casts and if they are interchangable? Thanks Jim
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top