(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. M

    To35 universal tractor fluid

    I have a 1955 TO-35. What transmission/hydraulic fluid is recommended? Can it use M2C-134D Ford spec oil? It is cold northern climate here and my hydraulics are very sluggish in teens temps I have now.
  2. M

    Fishing1

    I have a 1955 TO-35. What transmission hydraulic fluid is recommended? Can it use M2C-134D Ford spec oil?
  3. M

    TO-35 throttle/governor linkage adjustment

    I just bought a 1955 TO35 and the linkage is not right. The tractor when started goes right to 2200 rpm and moving throttle lever to idle position doesn't slow it. Does anyone have concise instructions on adjustment? I have an I&T manual I am having trouble understanding as it has little...
  4. M

    860 carb fills air inlet hose w/fuel.

    I have a 1955 ford 860 with MS carb with #593 and 3/1955 stamped on it's brass plate. It is filling up chamber above float and putting a cup or two of gas into the rubber hose air inlet, then it is flooded and won't start cold. I always turn fuel off when not in use. Fuel shutoff at tank is new...
  5. M

    timing marks for TO35 flywheel

    I put white paint on the six degree mark. Is this correct for my Z134 gas motor?
  6. M

    Removing front timing cover under water pump and oil pan

    Sending in to35 motor for complete overhaul. I got belt pulley off but can't get the timing chain cover off. Also need to pull oil pan and clutch assembly. Any tricks to this?
  7. M

    to-35 paint color

    I have a 1955 model to35 ser# 164776. What is the correct paint codes for that serial number? Is it the green or the red? I saw some early 55's with greenish body. I know they did 35's in both schemes. I pulled the engine today to rebuild it and it is red inside bell housing. The exterior has...
  8. M

    timing TO-35

    I just bought a 1955 TO35 and the timing is off. I have the number one piston in compression stroke but when I look in the bell housing inspection hole you can't see the timing marks at all due to awkward position. The steering linkage arms are in the way. Do I need an optical bore scope to...
  9. M

    timing TO-35

    I just bought a 1955 TO35 and the timing is off. I have the number one piston in compression stroke but when I look in the bell housing inspection hole you can't see the timing marks at all due to awkward position. The steering linkage arms are in the way. Do I need an optical bore scope to...
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top