(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. S

    Help with Hydraulic valve Power Beyond

    Hi, I want to add a remote (or two) to my IH 2444. Right now it does not have any. I have this valve (pictured) controlling my FEL. I think it is factory original but don't know for sure. I assume it may have power beyond ability (port) but I can not identify it. I can not find any name or...
  2. S

    low oil pressure

    I have a IH 2444 with a C153 engine that has developed low oil pressure at idle. I have a couple of questions in regards to that: I have been running 10W30 oil but I am thinking of changing to straight 30 (or even 40) for the summer. Is this OK? I plan to remove the oil pan and the oil pump...
  3. S

    Rear hydraulic remote

    Hi, I would like to add a rear remote to my 2444. The bolt on kit for the side of the lift box is nearly impossible to find and incredibly expensive. I would like to plumb one into the FEL valve somehow but I am not sure how to go about it. Any input would be appreciated. I attached a...
  4. S

    IHC2444 Wiring Diagram

    Hi All, The Wiring in my 2444 is a mess so it is time to clean it up/replace it all. I drew up a basic schematic (attached) of my start/charge/ignition/basic functions. I was hoping a couple of you electrical types could critique it for me. I want to make sure I got the regulator and charge...
  5. S

    External Regulator... or not

    Hi, My External voltage regulator on my IH2444 is shot. It puts out about 19volts! I have been debating replacing it with a new on or replacing the alternator with and internally regulated one instead. I have a good alternator that came off a 91 ford Ranger so replacing the alternator would...
  6. S

    2444 hydraulic fluid capacity

    I am really confused about the hydraulic fluid on my 2444. The lift box seems to drain into the differential. So I am worried that in order to fill the lift box I will over fill the gear box/transmission and the oil will start coming out of the transmission vent. What am I missing here?? I...
  7. S

    No fuel pump (fuel pump bypassed)

    Hi, Me agian.... hopefully I am not asking too many questions but you guys are a goldmine of info... Thanks so much. My next problem is I realized that the fuel pump on my IH2444 has been bypassed. The line comes right from the tank goes through and in-line filter and into the carb. In other...
  8. S

    PTO engaging clutch

    Hi, I have been working away at installing PTO in my IH2444 (same as 444) anyway the way the PTO engages and disengages is by a sliding collar that moves back and forth on the splined PTO shaft (part #5 in the image) either mating with the splined transmission shaft if the pto is engaged or...
  9. S

    Transmission cover

    Hi, I removed the Transmission cover that contains the shift leaver and all the forks/sliders. My question is how do I make sure that the the forks engage the transmission properly when I reassemble it. It seems to me that It would be quite possible to have the fork miss its match and thus the...
  10. S

    PTO pilot bushing on IH2444

    Hi, I just purchased all the parts to install a PTO on my IH2444 (which did not come with a PTO). However the pilot bushing that goes on the front of the PTO to mate the PTO with the transmission shaft does not fit over the end of the transmission shaft. However the PTO shaft fits nicely over...
  11. S

    gaskets

    Hi, I just pulled the Hydraulic reservoir and rockshaft housing off of my IH2444. The paper gasket came off nicely without any damage. What do you all think about reusing it. I would add some RTV gasket maker to it as well. Thanks for any advice you may have. Ian
  12. S

    hydraulic oil for 2444

    Hi, I have a IH 2444 (basically a 444) with PS and FEL. I was wondering what the current day recommended hydraulic/gear oil would be to use in this tractor. Thanks, Ian
  13. S

    3 pt hitch on a IH 2444

    Hi all, I have a IH2444 that was equipped for 3pt hitch but somebody removed the lover link arms and the lift arms. I know that the original lower link arms were 28" center of pin to enter of pin (feel free to confirm or correct if I am wrong). However what is the nominal length of the lift...
  14. S

    oil pressure guage on C153

    Hi I have an IH 2444 gas with a C153 engine. I would like to add an oil pressure guage to it. I am not sure where I should connect to the block? Has anyone done this on a C153? If so where did you attache the line up to the oil pressure guage. Thanks so much for your help. Ian
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top