(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. B

    Closing a Cold Shut Link

    Sorry. I meant to ask about a lap link. Thanks for replies tho.
  2. B

    Closing a Cold Shut Link

    How? (How does one close a cold shut link?)
  3. B

    560 steps??

    Harry R, I bolted a couple of pieces of angle iron in the “notches” of the left rear axle. One extended further down. Welded to that is another angle iron (horizontal), then welded a couple of draft horse shoes as the surface to step on. Helps me. Otherwise 300, 400, 350, 450, 460, 560 As you’ve...
  4. B

    JD55gascombine engine swap

    Any chance the gas engine from my John Deere 55 combine would fit my 1949 Chevy pickup without lotsa modification?
  5. B

    Farmall 300 N H 469 Haybine

    Thanks all!!! kelly
  6. B

    On Farm Gasoline Storage

    Thanks all. Lotsa good replies. My concerns are reduced greatly. FYI I won?t worry about theft cuz my place isn?t even visible from the county road. My drive is a full half-mile with a full 90 degree turn about 2/3 way. The tank is silver (allowed here in Texas) so it?ll reflect some sun...
  7. B

    Farmall 300 N H 469 Haybine

    1) should the Farmall 300 hydraulics be adequate to lift the cutter bar? 2) I'm not concerned about speed. Can the 300 handle a 9' New Holland 469 cutter conditioner?
  8. B

    On Farm Gasoline Storage

    Just bought a 250 gallon gasoline storage tank (on a stand). I have seven tractors and one large grain truck. All are gasoline except for one diesel. I'm tired of running to the gas station and buying five or ten gallons of gasoline at a time. I can also have bulk gasoline delivered cheaper than...
  9. B

    Janicholsen 300 Hydraulics Info

    OOPS, sorry for misspelling Nicholson.
  10. B

    Janicholsen 300 Hydraulics Info

    Thanks. Your help is much appreciated. kelly
  11. B

    Farmall 300 hydraulic repair

    I'm taking my 300 to a "general" mechanic for repair of my hydraulic system. Its just too far and too difficult to go to a CNHI shop. My hydraulics just are terrifically weak. For example, they won't lift my NH cutter/conditioner. They'll barely lift a three point shredder and wont lift it high...
  12. B

    1850 PTO WONT STOP

    Buddy says his 1850?s pto shaft turns/doesn?t stop. Can he adjust it to make it work correctly? Thanks
  13. B

    Gary??? In Muleshoe

    Gary (not sure that?s your name) I?m at Heritage Inn in Muleshoe. Gimme a call if you have nothing better to do. Kellyintx or big_red_man 512 627 7439
  14. B

    JD Seller

    Farnall 75C with 75 engine horses.
  15. B

    moonlight37 - Hesston in Mo

    Hi. I know nothing about a Hesston 5510 but there is a dealer nearby. I?m assuming your baler makes 4 by 5 bales??? I?d like to know asking price and approximate Missouri location. I?m assuming condition is usable??? Would your baler fit onto a trailer? It may be too far but I?m retired and like...
  16. B

    Dumb ? Using single blade hitch

    J D 1209 (or 1219) cutter/conditioner. It has a single ?blade? tongue with a hole in it. My tractor drawbar has a single blade with a hole. Do i just drop a pin through to connect the two??? Thanks, Kelly
  17. B

    JD Moldboard Plow 4 Bot To 3???

    After a divorce my neighbor has a four bottom plow. It looks like an F145. It. Has a trailer wheel and three point hitch. It hasn?t been used for several years. Would it be easy to change it to a three bottom? (I don?t have enuf tractor oomph to pull a four bottom.) thanks, Kelly
  18. B

    Small, cheap round baler suggestions

    J D, my tractor is a Farmall 75C. It has 75 engine horsepower. I do small fields and small amounts of hay. A summer with rain might be 500 small square bales. This summer there has been no rain virtually. BUT, sometimes we get fall rains here in south/south central TX. One year I made hay in...
  19. B

    Freddy Driebrodt Passed

    Don?t believe he ever posted or read but Freddy of San Marcos, TX recently passed. He was a neighbor, third generation farmer and loved his Oliver tractors. I suspect his widow still has the roughly 10-12 diesels that are still in his barns. His widow says they made several trips (mostly north)...
  20. B

    H or m Farmall

    I agree with John. My very early ?39 is an upside down ?U? channel and NOT a pipe.
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top