(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. M

    4430 has a miss

    Everyone, I purchased a 4430 this year and it has been an awesome tractor. Tons of power, was told the engine had 500 hours on it but sat in the shed and used very little for about 10 years. I noticed the other day it sounds like it has a slight miss. Where should I start looking? I...
  2. M

    John Deere 318 mower

    We have one that keeps blowing a fuse as trying to start it. I do not see any pinched or ground out wires, any ideas??
  3. M

    Farmall M M&W Hand Clutch

    Anyone know if I can get parts, and how to put it back together? Got a tractor in a box, and would love to get it running. I think all parts are there, but steel discs are rusted! Matt
  4. M

    IH 856 engine

    I have a student looking for a 856 Diesel engine that is running, new or rebuildable. Current engine has a big whole in the block. We are in Iowa and would like something fairly close, but are wiling to travel depending on what it is. email me please [email protected]
  5. M

    AGCO AxlE Extentions for Duals

    I purchased axle extensions with AGCO Centers (like oliver) 20.8x38 Rear tires and centers. I used the heavy cast centers and rims for a converting my Cummins project to 20.8x38 rear tires. I have these and not sure what are called, and would like to see them go to be used. The came off a...
  6. M

    Case 1290 Parts and issues

    I have it sitting right here in my gasket kit. Thank you! Matt
  7. M

    Case 1290 Parts and issues

    Also does that rubber, have a hole all the way through it?? Of is it solid? Matt
  8. M

    Case 1290 Parts and issues

    Two wheel drive, and thank you. Matt
  9. M

    1750 PTO

    OK, can you put a 1000 pto on this tractor? do you use the top port? Wondering, if Yes, do some people have them both hooked up? Matt
  10. M

    Case 1290 Parts and issues

    I have finishing up a complete overhaul on my 1290 case and ran into a few issues. 1. ON the bottom side of the thermostat housing, there is a hole that is not threaded. I believe the machine shop removed whatever was in the hole when they rebuilt the head, and I never received the part...
  11. M

    Case 1290 Parts and issues

    I have finishing up a complete overhaul on my 1290 case and ran into a few issues. 1. ON the bottom side of the thermostat housing, there is a hole that is not threaded. I believe the machine shop removed whatever was in the hole when they rebuilt the head, and I never received the part...
  12. M

    Looking for AC C parts.

    I am looking for the following in good condition prefer close to iowa, wis, il. Fuel Tank (not rusted to beat hell) Components to switch to distributor. Battery box Hood and maybe a grill Let me know Matt
  13. M

    oliver rims hub question

    Yes, picked them up today. I am looking forward to a new set of tires on there and mounting them this week. What tractors ran the 166 217A hubs???? Matt
  14. M

    44 partial lock up with head pulled off

    I purchased a 44 that was assumed locked up. Tried pulling it and tires drug as well. I pulled the start off and found some chips in the rear, found out a small piece was wedged between the flywheel and the bellhousing. I would check that, if would be loose and hit hard in my case as well...
  15. M

    oliver rims hub question

    Currently have 166 218A Hubs and looking at 166 217A hubs. Believe that the 218A are for 34' double bevel and the 217 are for 38 double bevel. Correct me if I am wrong, but both should have same bolt pattern?
  16. M

    oliver rims hub question

    I have a 1750 with the 13 old (3 whole, 3whole, 1 whole, 5 whole, one whole pattern) and wondering if the hubs off a Deutz ST140 would fit that have the same style hubs only 38inch verse 34 inch. Hoping that the center hub will fit on my axle hub. Matt
  17. M

    Case 1290 injectors

    Does anyone know where I can find one and about the cost? I need 4 total.
  18. M

    h farmall

    Where are you both from? That is cheap for a tractor where I am from. Usually c is about $1000+ for junk and H is like $1200+
  19. M

    13.6x38 Titan Tires

    So tires alone about $500-550 each?
  20. M

    engine transplant 1750

    I did bought a 1850 for the tub, frount end, bellhousing and a few other parts. The costly stuff is hte flywheel to bolt to a cummins, hub and clutch. But I know it is done right as well. The $2000 is the Wide frount end to the tractor everything i needed minus the engine.
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top