(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. A

    case sc oil

    Thanks good point it’s only hooked to the two point hitch and has no remotes plumbed in but you never know what may happen in the future for now the plan is for raking hay
  2. A

    case sc oil

    Thanks it must be newer as it has factory hydraulics I think we used 30 weight in the past but not sure
  3. A

    case sc oil

    I have a case sc that has been sitting in a barn for about 8 years or so and I decided I needed another tractor and decided to get it operational again. It wasn't to hard to get it running again but I wanted to change the fluids in it after sitting so long. I'm wondering what is recommended for...
  4. A

    farmall 460 hydraulics

    I don’t think so the filter was replaced recently and the oil is full when I took it apart the second time it had oil in the valve so it gets there just not building pressure I’ll need to take it back apart and see if I can figure out if the relief valve is indeed stuck
  5. A

    Farmall 560 clicking wheel

    As stated it sounds like the bolts attaching the wheel to the axle. I've had the same issue in the past. I would take the weight off the wheel and remove the bolts and clean and perhaps add a washer if you think they may be bottoming out and when tightening them use a impact or a breaker bar...
  6. A

    farmall 460 hydraulics

    Thanks, it seems the valve is stuck and not letting it build pressure, is there a way to get it out? I am thinking about leaving the spring out and starting the tractor to see if it will push it against the cover
  7. A

    farmall 460 hydraulics

    Forgot to mention when I first put it together the big spring wouldn’t compress enough so I took the cap off and turned the piston a little and it dropped in further and things went together as they should now the piston is tight and I can’t get it out where before it would slide out
  8. A

    farmall 460 hydraulics

    Thanks but I didn’t drill the hole out mostly just opened up the screen which had collapsed but was pretty clean as was the hole
  9. A

    farmall 460 hydraulics

    Following up on an earlier post regarding hydraulics on my 460. I have taken the regulator/safety valve off to clean and check the screen, when I reassembled and installed I had no hydraulics at all. I assumed I had assembled something incorrectly so took it back off and disassembled again...
  10. A

    460 relief valve

    I probably would of figured that out if I had been able to get the unloader valve apart as that one is pretty big I was able to take the screen out and looks like somebody already removed that ball anyway I cleaned everything up and put back together and reinstalled but now have no hydraulics at...
  11. A

    460 relief valve

    Thanks Pete that would explain why I was having so trouble with what sounded fairly simple I’ll tackle it tonight
  12. A

    460 relief valve

    Thanks Pete that explains why I was having so much trouble with something that sounded fairly simple I’ll tackle it tonight
  13. A

    460 relief valve

    Thanks I've got one of those already but the blade is maybe 3/8 at best and the ball is about the same size so I don't think it will catch enough of the edges to work I've ground down a 7/8 cold chisel to fit the slot but can't turn it with a wrench on it
  14. A

    460 relief valve

    Thanks Jim but that picture is from an different post my issue now is just getting it apart any trick to unscrew the seat ?
  15. A

    460 relief valve

    I have been having issues with the tractor always being under load and have decided it is most likely the screen in the relief valve I have pulled the valve body off and taken it apart but have been unable to unscrew the seat I have taken a chisel and ground it down to make a tool but it still...
  16. A

    560 hyd pump always in labor

    I have been having the same issue with my 460 and have decided to take it apart, does anyone have advice on how to take the threaded plug out as I don't have a screwdriver that large and it's kind of a pain to make something that works. Also I seem to remember folks saying to just take the ball...
  17. A

    Farmall H Issues

    I agree you should check the coil since you said it has a weak spark, sometimes the coil works ok when cold but acts up when it gets hot. They are cheap enough or if you have another one off something else you can try to see if that solves the issue
  18. A

    460 pto

    I have a couple of 460's and have the same issue with a "drag" on the PTO. It turns all the time so I have to turn the tractor off to hook any thing up. However when anything is hooked to it the equipment does not run and you can engage of disengage the PTO to stop the equipment. Probably not...
  19. A

    international farmall tractors

    Rustred was correct in checking the points, also if you use a screwdriver to open them to check spark also use the screwdriver to "short" the points to the side of the distributor, it should have a bright spark. If you have a hot spark there and not so good across the points chances are the...
  20. A

    460 carb icing

    Thanks, I remember the springs on the manifolds but never knew what they were for. I'm pretty sure that they are most likely rusted up so I will take a look and see if I can get it working. I only use one tractor in the winter for moving hay so I'll start with that one.
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top