(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. E

    IH 560

    they made a tillage 3rd gear made 3rd slower change the RP I think the 400 will speed things up if my memory is write getting old lol
  2. E

    John Deere A

    Make the rods longer get them write up there and don't forget to notch the piston more for the spark plug
  3. E

    John Deere B

    9-1 compression will make it pretty snappy
  4. E

    John Deere A power block

    For what you will have in a PB better off strokeing it
  5. E

    Super H Options

    350 block pull the sleeves run 301 pistons and 350 lp head
  6. E

    G JD

    We use clay to check valve to piston clearance
  7. E

    G JD

    I had a Lot more than that on a A didn't have any problems
  8. E

    Model M idele problems

    Got a model M will not idele smooth rebuilt carb seems like it sucking air some were am I missing something any help would be appreciated
  9. E

    ih 301 crankshaft

    yes works very good
  10. E

    Cooling system pressure

    Put electric pump on problem solved my supper stock tractors all did it rpm is couseing it
  11. E

    4020 carb

    Does anyone know the throttle bore size on a 4020 zenith carb thanks
  12. E

    Bendix carb running lean

    Got a bendix carb running lean on top end drilled main jet still lean any suggestions thanks
  13. E

    hi torqe starter for a 1944 b

    Looking for a hi torqe starter for a top mount B
  14. E

    1944 B hi tourqe starter

    whats a good hi tourqe starter for a 1944 B top mount
  15. E

    Governor spring

    Hard ware store
  16. E

    rubber seals in 460 motor

    what do the two push in rubber tubes do in the main bearing cap do in the rear of the motor
  17. E

    aluminium inserts

    Who was selling the inserts to go inside the rims
  18. E

    silver diamond truck head

    yes you can but you will need the rockerarms and valve cover too
  19. E

    460 grill

    were can I get the aluminium that goes on top of the grill
  20. E

    emblems on a 460

    does any one know the size of the holes that the emblem push in too I have some that are to big and don't hold the clips that go into them thanks
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top