(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. R

    40b won't move

    Thanks for the reply I here what your saying but even with the cotter pin in it still slides to far in one direction
  2. R

    40b won't move

    Happy New year everybody, I have a my 40B its a manual shuttle ,while driving it the other day the tractor just stopped moving I was in high gear at the time it would move a couple more times but only for a few feet.I tried every gear but no movement. The first thing I thought of was the...
  3. R

    54 naa

    Great, just wanted to make sure before I broke something ,thanks for the explanation.
  4. R

    54 naa

    Need some help on my NAA I need to replace the lift ram arm (broken) I can get the lift arm shaft to go only so far. In the parts book it looks like the shaft is bigger in the center so then it would be bigger then the bushings? So how does it come out? Thanks
  5. R

    NAA no lift power

    okay thanks, it looks like it's time to pull the lift cover
  6. R

    NAA no lift power

    yes it does lift but won't support or hold when weight is applied. I have removed some access covers and can see a lot of leakage of oil where the lift cyl is bolted to the lift cover I think there is a gasket there possibly blown out.
  7. R

    NAA no lift power

    HI, Need some help with my NAA three point will lift but won?t hold a load ,I want to check they pump pressure to start but don?t know where the access point is.Tanks
  8. R

    2n hyd pick up tube

    thanks that was a huge help, I think I'll try and remove it first just to make sure nothing else goes amiss.
  9. R

    2n hyd pick up tube

    thanks for the reply, so did I understand you have them for purchase? also what's the correct way to get that out of there it looks like I pull the pump down from the bottom first.
  10. R

    2n hyd pick up tube

    need some help with my 2n noticed recently my three point would go up but wouldn't hold weight. I found the pick up tube from the pump to the rockshaft piston has a split in it. I can't find any available parts ,could fix it but would rather replace it if possible.
  11. R

    235 block core plug

    ill ck that out tonight
  12. R

    235 block core plug

    need some help on a 235 diesel, I'm replacing a head gasket and noticed some coolant passages in the block have core plugs in them with holes i'm guessing t slow down coolant flow, these plugs are corroded and should be replaced but I can't find them in the parts breakdown. has anyone seen this...
  13. R

    580b brake seal leak

    mEI Was right on I was able to modify a pick and fish them out, there ended up being (4) seals stuffed in there so thanks so much for the help. the reason I did the seals was because of the oil leakage on the brake linings. I replaced all the friction material and adjusted all the linkage to...
  14. R

    580b brake seal leak

    thanks so much that was very helpful, it looked like in the picture there are two seals that go in there is that correct?
  15. R

    580b brake seal leak

    ok thanks just seems so tight to get anything in there.
  16. R

    580b brake seal leak

    need some help with my 580 I'm resealing a rt side seal leak that saturated the brake linings. I found some posts on how to replace the larger seal but I need to replace the smaller seals (2) around the differential lock shaft. can I remove the whole assembly? doing it in the vehicle seems very...
  17. R

    farmall A fuel leak

    thanks for all your reply's, the carb is a marvel/schebeler I believe the needle is a rubber tiped. I have already replaced the seat to body gasket but good idea.
  18. R

    farmall A fuel leak

    HI,I have a Farmall A that I can't get the carb to stop leaking when it's not in use. I have to shut off the needle valve in the sediment bowl or fuel will continuously drip from the carb throttle and bowl to cover gasket. I have went through the carb replaced needle and seat, changed the float...
  19. R

    1715 ford

    yes your right mark that's what I didn't do, before I put it back together. so I used the gasket thickness that would have been factory. which I would guess would be the thinnest.
  20. R

    1715 ford

    HI, I have a ford 1715 with a j843 engine I just rebuilt it. 1. engine was bored over.040 block was decked. 2. valve job, head was resurfaced 3.new pistons, rods bushings replaced and fitted. 4. rod and main bearings replaced. after starting engine after careful break in 60 psi oil pressure,190...
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top